You searched and this document matched it.
See all results045555 · Installation Guide · Rev B · Oct 2016 · English, French, Spanish, Italian, German, Chinese, Portuguese · PDF, 1 page, 1.6 MB
Lutron Installation Guide: Wireless RF Receiver, Basic Wiring and Setup (045555)
Lutron's installation guide for the Sivoia QS Wireless RF receiver, the plug-in module that gives a drive wireless control.
Lutron 045555 Rev B (October 2016), Installation Guide: Wireless RF Receiver, Basic Wiring and Setup. https://assets.lutron.com/a/documents/045515.pdf, via https://newwaykl.com/resources/documents/lutron-installation-guide-045555/
About document 045555
Lutron document 045555, Rev B of October 2016, is the one-page RF receiver installation guide: box contents, the plug connection, two mounting options, antenna placement, control assignment and the five receiver models by frequency.
What guide 045555 covers
Lutron document 045555 has these seven sections, all on its one page.
- Contents
- Connect the receiver to the window treatment drive
- Mount the wireless receiver
- Position the RF antenna
- Assign a wireless control
- Important notes
- Receiver models by frequency
Specifications in 045555
Lutron document 045555 prints 17 values in the groups the document uses, each with the document's unit. A row names the catalog codes it applies to. The page link beside each group opens the PDF where the group starts.
- Wireless receiver
- 1, with window treatment drive connector and RF antenna
- Antenna clips
- 2, with mounting tape
- Cable ties
- 3
- Receiver mounting bracket
- 1, mounting tape pre-applied
- Mounting screws
- 2
- Frequency
- 434 MHzModels: QSYC-J-RCVR
- Frequency
- Limited 434 MHzModels: QSYC-Q-RCVR
- Frequency
- 865 MHzModels: QSYC-N-RCVR
- Frequency
- 868 MHzModels: QSYC-K-RCVR
- Frequency
- Limited 868 MHzModels: QSYC-M-RCVR
Important Notes
PDF page 1 of 045555, opens in a new tab- Ambient operating temperature
- 32 °F to 104 °F (0 °C to 40 °C)
- Humidity
- 0 to 90%, non-condensing
- Location
- Indoor use only
- Wiring and circuit protection
- To national and local electrical codes
Assign a Wireless Control
PDF page 1 of 045555, opens in a new tab- Assignment mode signal
- Drive LED and receiver LED flash green every 4 seconds
- Hold to complete assignment
- 6 seconds on the Close button; on a 4-Group remote, 6 seconds on a shade group button (1, 2, 3, 4 or All)
- Confirmation
- Treatment moves a short distance (wiggle)
Installation walk-through for 045555
Lutron document 045555 gives seven steps, in the document's order, after the fixings it lists.
The clearance, the check and the warning under a step are the document's own.
Fixings
- Two mounting screws (provided), or other fasteners suited to the surface
- Self-adhesive receiver mounting bracket, tape pre-applied (provided)
- Two antenna clips with mounting tape (provided)
- Screws for the antenna clips (not included)
- Three cable ties (provided)
Check the contents
Open the box and confirm the five items. Expect the receiver with its drive connector and RF antenna, two antenna clips with tape and three cable ties.
The mounting bracket comes with its tape already applied, plus two mounting screws.
Check: All five items present
Connect the receiver to the drive
Plug the receiver's window treatment drive connector into the RF connector that leads from the drive. Route every wire clear of the moving treatment and fix the wires with the cable ties supplied.
Check: No wire can interfere with the normal movement of the treatment
Mount the receiver
Choose one of two methods. Screw the receiver to window trim or a nearby surface, with the supplied screws or fasteners that suit it.
Alternatively, peel the backing off the self-adhesive bracket and press it onto the drive, headrail, track or a nearby surface. Push the receiver into the bracket.
Check: Adhesive bracket pressed firmly onto its surface before the receiver goes in
Position the RF antenna
Fix the antenna clips with the tape supplied or with screws (not included), then clip the antenna in place. With the receiver mounted in the open, the antenna can sit close above or below it.
With the receiver in a pocket, behind a fascia or near signal-blocking metal, place the antenna outside that structure.
Check: Antenna outside any metal structure around the receiver
Warning: Power supplies, wiring and other current-carrying devices near the antenna can weaken RF performance. Keep the antenna as far from them as possible.
Prepare the window treatment
On the drive, double-tap the Open Limit button. The treatment runs to the fully open position and the drive LED turns off.
Check: Treatment fully open and drive LED off
Enter assignment mode
On the drive, hold the Open Limit button down until its LED flashes green and then stays lit. Let go and tap the arrow button beside the LED.
The drive LED and the receiver LED now flash green every 4 seconds. Repeat steps 5 and 6 for every treatment and receiver the same control will operate.
Check: Every treatment to be assigned shows the green flash every 4 seconds
Complete the assignment
On the wireless control, hold the Close button down for 6 seconds. The button can look different from one control to another.
On a 4-Group remote, hold one shade group button instead, 1, 2, 3, 4 or All, for 6 seconds. Each treatment moves a short distance, a wiggle, to confirm the assignment.
Check: Every treatment in assignment mode wiggled
Requirements Lutron states in 045555
What the guide requires for a Lutron shade before and during installation:
- In the box
- One wireless receiver with drive connector and RF antenna
- Two antenna clips with mounting tape
- Three cable ties
- One mounting bracket with tape pre-applied
- Two mounting screws
- Receiver models
- 434 MHz: QSYC-J-RCVR
- 434 MHz, limited: QSYC-Q-RCVR
- 865 MHz: QSYC-N-RCVR
- 868 MHz: QSYC-K-RCVR
- 868 MHz, limited: QSYC-M-RCVR
- Connection
- The receiver's drive connector plugs into the RF connector that comes from the window treatment drive
- Wire routing
- All wires arranged and fixed with the three cable ties supplied so they stay clear of the moving treatment
- Mounting, screws
- Screwed to window trim or a nearby surface
- Mounting, bracket
- Pushed into the self-adhesive bracket stuck to the drive, headrail, drapery track or another nearby surface
- Antenna fixing
- Antenna clips held by the mounting tape supplied, or by screws that are not included
- Antenna placement
- As far as possible from power supplies, wiring and anything carrying current
- Close above or below the receiver when it is in the open
- Outside any pocket, fascia or metal structure that would block the signal
- Assigning a control
- Double-tap Open Limit on the drive
- Hold Open Limit until the LED flashes green and stays on
- Tap the arrow button: both LEDs flash green every 4 seconds
- Hold the control's Close button for 6 seconds until the treatment wiggles
- Environment
- 32 °F to 104 °F (0 °C to 40 °C), 0 to 90% humidity non-condensing, indoor use only. Wiring and circuit protection to national and local codes.
- Further setup
- Detailed Sivoia QS setup is referred to P/N 045314, the Sivoia QS wiring and programming guide
Questions about document 045555
The answers come from Lutron document 045555 and New Way's record of it.
What is Lutron document 045555?
Lutron's one-page sheet, printed P/N 045555 Rev B, 10/2016, served under the file name 045515. The sheet repeats every step in six further languages on the same page.
Which revision of 045555 is current?
Rev B, dated October 2016, is the revision Lutron publishes. New Way checked it against assets.lutron.com on 15 October 2026.
Which receiver model suits which frequency?
Five receiver models by frequency, per Lutron document 045555, all installed the same way.
- 434 MHz: QSYC-J-RCVR, or QSYC-Q-RCVR for limited 434 MHz
- 865 MHz: QSYC-N-RCVR
- 868 MHz: QSYC-K-RCVR, or QSYC-M-RCVR for limited 868 MHz
What operating conditions does the receiver need?
Indoor use only at 32 °F to 104 °F (0 °C to 40 °C), per Lutron document 045555, and 0 to 90% humidity, non-condensing. Wiring and circuit protection follow national and local electrical codes.
Where should the antenna go?
As far as possible from power supplies, wiring and other current-carrying devices, per Lutron document 045555. In the open it can sit close above or below the receiver.
With the receiver in a pocket, behind a fascia or near metal, the antenna goes outside that structure.
How is a shade assigned to a wireless control through the receiver?
Lutron document 045555 pairs a treatment in three moves, confirmed by a short wiggle of the treatment.
- Double-tap Open Limit on the drive to open the treatment
- Hold Open Limit, then tap the arrow button, to enter assignment mode
- Hold the control's Close button for 6 seconds to complete
Can one control be assigned to several treatments at once?
Yes: Lutron document 045555 puts each treatment and its receiver into assignment mode one after another. A single 6-second hold on the control then completes all of them.
On a 4-Group remote, a shade group button (1, 2, 3, 4 or All) replaces Close.
How is the receiver mounted, and can it be hidden?
Lutron document 045555 screws the receiver to window trim or a nearby surface, or seats it in the self-adhesive bracket. The bracket sticks to the drive, headrail or drapery track.
A pocket or fascia location is allowed as long as the antenna is fixed outside any metal structure.
Documents used with 045555
Lutron documents 045450, 045415 and 045985 are drive installation guides in the same library (horizontal sheer blinds, Drapery Lite). Lutron document 045555 points to P/N 045314, the Sivoia QS wiring and programming guide; Lutron serves this file as 045515.
| Document | Type | Revision | Date |
|---|---|---|---|
| 045314Sivoia QS Roller Shades Installation Guide | Installation Guide | B | Jun 2014 |
Revisions of 045555
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| B | Oct 2016 | Current. The file on assets.lutron.com. Checked 15 Oct 2026. |
Not covered in 045555, and what to read next
Lutron document 045555 covers no drive mounting, wiring or limit setting, and no programming beyond assigning a wireless control.
Publisher and citation for document 045555
Lutron Electronics Co., Inc. publishes document 045555, Rev B, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 15 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Lutron?
New Way supplies and installs Lutron shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 045555 filled in.
