You searched and this document matched it.
See all results045314 · Installation Guide · Rev B · Jun 2014 · English · PDF, 20 pages, 2.0 MB
Lutron Sivoia QS Roller Shades Installation Guide (045314, rev B)
Lutron's Sivoia QS wiring and programming guide, a 20-page reference for wiring and commissioning Sivoia QS drives once mounted.
Lutron 045314 Rev B (June 2014), Sivoia QS Roller Shades Installation Guide. https://assets.lutron.com/a/documents/045314 qs wp guide.pdf, via https://newwaykl.com/resources/lutron/roller-shades/sivoia-qs/lutron-sivoia-qs-roller-shades-installation-guide-045314/
About document 045314
Lutron document 045314, Rev B of June 2014, is the Sivoia QS wiring and programming guide: the 24 V DC link wiring, the wire length chart, limits, link checks, keypad assignment, presets, resets and troubleshooting.
What guide 045314 covers
Lutron document 045314 has these twelve sections. Each link opens the PDF at that page in a new tab.
- System wiring overview: QS link power supply, opens in a new tab page 4
- Smart panel wiring, opens in a new tab page 5
- GRAFIK Eye QS integration wiring, opens in a new tab page 8
- QS power supply wiring and wire length chart, opens in a new tab page 9
- Setting limits from the drive, opens in a new tab page 10
- Verify communication from drive or smart panel, opens in a new tab page 11
- Assigning window treatments to keypads, opens in a new tab page 12
- Setting limits from a keypad or IR transmitter, opens in a new tab page 13
- Storing presets from a keypad or IR transmitter, opens in a new tab page 14
- Individual level adjust, opens in a new tab page 15
- Restoring drive and keypad default settings, opens in a new tab page 16
- Troubleshooting chart and limited warranty, opens in a new tab page 18
Specifications in 045314
Lutron document 045314 prints 23 values in the groups the document uses, each with the document's unit. A row names the catalog codes it applies to. The page link beside each group opens the PDF where the group starts.
System Wiring Overview
PDF pages 2 and 4 of 045314, opens in a new tab- Drive and keypad supply
- 24 V DC
- Shade or drapery drives per power supply output
- 1 maximum
- Keypads on the link (example)
- Up to 8
- Power and communication link
- 4 conductor
- Communication link between supplies or to GRAFIK Eye QS
- 3 conductor
- Secondary wiring
- CL2, CL2P, CL2R, CL2X or cable with equivalent or better ratings
Smart Panel System Wiring
PDF page 5 of 045314, opens in a new tab- Smart panel power supply
- 10 outputs, fed at 120 V~ 60 HzModels: QSPS-P1-10-60
QS Smart Panel Power Supply (QSPS-Px-10-60)
PDF page 9 of 045314, opens in a new tab- No shade or drapery, up to 50 power draw units
- 1250 ft (375 m) on 12 AWG (4 mm²); 500 ft (150 m) on 16 AWG (1.5 mm²); 250 ft (75 m) on 18 AWG (1 mm²)Models: QSPS-Px-10-60
- No shade or drapery, up to 25 power draw units
- 2000 ft (600 m) on 12 AWG (4 mm²); 1000 ft (300 m) on 16 AWG (1.5 mm²); 600 ft (175 m) on 18 AWG (1 mm²)Models: QSPS-Px-10-60
- 1 Sivoia QS shade or drapery, up to 1 power draw unit
- 500 ft (150 m) on 12 AWG (4 mm²); 200 ft (60 m) on 16 AWG (1.5 mm²); 125 ft (35 m) on 18 AWG (1 mm²)Models: QSPS-Px-10-60
- 2 Roller 64, 30 ft² (2.75 m²) or less each, up to 1 power draw unit
- 200 ft (60 m) on 12 AWG (4 mm²); 75 ft (20 m) on 16 AWG (1.5 mm²); 50 ft (15 m) on 18 AWG (1 mm²)Models: QSPS-Px-10-60
- 3 Roller 64, 20 ft² (1.8 m²) or less each, up to 1 power draw unit
- 200 ft (60 m) on 12 AWG (4 mm²); 75 ft (20 m) on 16 AWG (1.5 mm²); 50 ft (15 m) on 18 AWG (1 mm²)Models: QSPS-Px-10-60
- 2 Roller 100, 50 ft² (4.6 m²) or less each, up to 1 power draw unit
- 200 ft (60 m) on 12 AWG (4 mm²); 75 ft (20 m) on 16 AWG (1.5 mm²); 50 ft (15 m) on 18 AWG (1 mm²)Models: QSPS-Px-10-60
- Cables for the 2 power conductors
- 12 AWG (4 mm²): QSH-CBL-L-500 or QSH-CBLP-L-500; 16 AWG (1.5 mm²): QSH-CBL-M-500 or QSH-CBLP-M-500; 18 AWG (1 mm²): GRX-CBL-346S-500Models: QSH-CBL-L-500, QSH-CBLP-L-500, QSH-CBL-M-500, QSH-CBLP-M-500, GRX-CBL-346S-500
QS Individual Power Supply (QSPS-Px-1-50 or QSPS-J-1-50)
PDF page 9 of 045314, opens in a new tab- No shade, up to 8 power draw units
- 2000 ft (600 m) on 12 AWG (4 mm²) or 16 AWG (1.5 mm²); 1500 ft (450 m) on 18 AWG (1 mm²)Models: QSPS-Px-1-50, QSPS-J-1-50
- 1 Sivoia QS shade or drapery, up to 1 power draw unit
- 250 ft (75 m) on 12 AWG (4 mm²); 100 ft (30 m) on 16 AWG (1.5 mm²); 50 ft (15 m) on 18 AWG (1 mm²)Models: QSPS-Px-1-50, QSPS-J-1-50
Verify Communication
PDF page 11 of 045314, opens in a new tab- Link diagnostics indication
- Treatments wiggle and flash a green LED once per second
Programming
PDF page 12 of 045314, opens in a new tab- Hold time to enter, store or exit a programming mode
- 5 seconds
Restoring Keypad Default Settings
PDF page 17 of 045314, opens in a new tab- Hold on the third tap
- About 3 seconds, until the top LED is solid
Troubleshooting
PDF page 18 of 045314, opens in a new tab- IR transmitter range
- Within 30 ft of the IR receiver, with line of sight
Limited Warranty
PDF page 19 of 045314, opens in a new tab- Drive, fabric and hardware
- 8 years from shipment
- Wall controls, interfaces and system accessories
- 1 year from shipment
- Replacement part credit
- 100% up to 5 years; 50% from 5 to 8 years; 0% after 8 years
Installation walk-through for 045314
Lutron document 045314 gives eleven steps, in the document's order.
The clearance, the check and the warning under a step are the document's own.
Size each output from the wire length chart
Use the section 6 chart of Lutron document 045314 to size each output. The chart gives how many shades and controls one output may carry for the shade sizes on the job.
Then confirm the longest run for that load on the gauge chosen for the two power conductors.
Clearance: One shade per smart panel output: 500 ft (150 m) on 12 AWG (4 mm²), 200 ft (60 m) on 16 AWG (1.5 mm²). On 18 AWG (1 mm²), 125 ft (35 m).
Check: Every planned run is inside the chart limit for its load and gauge.
Set the open limit at the drive
Lutron recommends setting limits at the drive first. Tap Open Limit (green LED on) and hold either arrow button to run the treatment to the open position.
Then hold Open Limit until the green LED flashes.
Check: Green LED flashed: open limit stored.
Set the close limit at the drive
Tap Close Limit (green LED on) and hold an arrow button to reach the close position. Then hold Close Limit until the green LED flashes.
Check: Green LED flashed: close limit stored.
Check the link from a drive
Hold Close for 5 seconds, then tap CCW to enter link diagnostics mode. Every treatment on the link wiggles and flashes a green LED once per second; hold Close to leave.
Check: Any treatment that does not wiggle, or shows a red LED, has its wiring checked.
Or check the link from the smart panel
At the Sivoia QS smart panel, tap Open and then hold it for 5 seconds, and do that twice. All treatments wiggle; a 5-second hold on Open exits the mode.
Assign treatments to a keypad
Hold Open and Close together for 5 seconds: assigned treatments close, unassigned ones open. Step through treatments with Open or Close, tapping Lower to assign or Raise to unassign.
Hold Open and Close 5 seconds to exit.
Set limits from a keypad or IR transmitter
Hold Open and Raise together for 5 seconds and select a treatment with Open or Close. Move it with Raise or Lower.
Save the open limit with a 5-second hold on Open, or the close limit with Close. Exit with Open and Raise held for 5 seconds.
Store a preset
Bring the treatment to the position wanted with Raise or Lower, then hold the chosen Preset button for 5 seconds.
Adjust single treatments within a preset
Hold Open and Lower together for 5 seconds, then tap the preset to enter preset-adjust mode. Select a treatment with Open or Close and set it with Raise or Lower, repeating for each treatment to change.
Lutron numbers the exit, Open and Lower held for 5 seconds, as step 12.6. The store, the preset held for 5 seconds, is step 12.7.
Restore drive defaults
Hold Close Limit, then Open Limit, then the CW arrow, then the CCW arrow. Hold each until the LED flashes green and stays on.
The LED runs a multicolor sequence and goes out.
Check: Keypad assignments are cleared; the open and close limits are kept.
Restore keypad defaults
Triple tap the top button, holding the third tap until its LED is solid, about 3 seconds. Release, triple tap again, and wait for the fast flashing to stop.
Check: Flashing stopped: the keypad is at factory settings.
Warning: Do not let go of the button after the third tap of the first sequence.
Requirements Lutron states in 045314
What the guide requires for a Sivoia QS shade before and during installation:
- System and power
- Drives and keypads run from a 24 V DC supply. One link carries power and communication to every drive, keypad and control, with or without GRAFIK Eye QS.
- Drives per power supply output
- A maximum of one shade or drapery drive per output of a QS link power supply. Up to 8 keypads on a link.
- Link cable types
- Power and communication link: 4 conductor
- Communication only, between supplies or to a GRAFIK Eye QS: 3 conductor
- Secondary wiring CL2, CL2P, CL2R, CL2X or equivalent
- Smart panel
- QSPS-P1-10-60, a 10-output smart panel fed at 120 V~ 60 Hz. Two or three Roller 64, or two Roller 100, may share an output depending on shade size.
- Smart panel, one shade
- One shade or drapery with up to 1 power draw unit per output:
- 500 ft (150 m) on 12 AWG (4 mm²)
- 200 ft (60 m) on 16 AWG (1.5 mm²)
- 125 ft (35 m) on 18 AWG (1 mm²)
- Smart panel, shared output
- Shared outputs take up to 1 power draw unit, with shorter runs.
- Two Roller 64 of 30 ft² (2.75 m²) or less
- Three Roller 64 of 20 ft² (1.8 m²) or less
- Two Roller 100 of 50 ft² (4.6 m²) or less
- 200 ft (60 m) on 12 AWG (4 mm²)
- 75 ft (20 m) on 16 AWG (1.5 mm²)
- 50 ft (15 m) on 18 AWG (1 mm²)
- Individual supply, one shade
- QSPS-Px-1-50 or QSPS-J-1-50, one shade or drapery with up to 1 power draw unit:
- 250 ft (75 m) on 12 AWG (4 mm²)
- 100 ft (30 m) on 16 AWG (1.5 mm²)
- 50 ft (15 m) on 18 AWG (1 mm²)
- Individual supply, PDUs only
- No shade and up to 8 power draw units:
- 2000 ft (600 m) on 12 AWG (4 mm²) or 16 AWG (1.5 mm²)
- 1500 ft (450 m) on 18 AWG (1 mm²)
- Factory reset
- A drive reset clears every keypad assignment but keeps the open and close limits. A keypad reset is a triple tap and hold on the top button, then a second triple tap.
- Infrared control
- Treatments can take a QS IR Eye receiver and a hand-held infrared remote. The troubleshooting chart wants line of sight within 30 ft of the receiver.
Questions about document 045314
The answers come from Lutron document 045314 and New Way's record of it.
What is Lutron document 045314?
Lutron's 20-page Sivoia QS wiring and programming guide, P/N 045314 revision B, dated 06/2014 on its back cover. The guide covers draperies, roller shades, venetian blinds, sheer blinds and tensioned shades, alone or with GRAFIK Eye QS.
Which revision of 045314 is current?
Rev B, dated June 2014, is the revision Lutron publishes. New Way checked it against assets.lutron.com on 15 October 2026.
Which roller shades does 045314 cover?
Lutron Sivoia QS roller shades.
How far can power wiring run from a smart panel output?
Up to 500 ft (150 m) on 12 AWG (4 mm²) for one shade per output, from Lutron document 045314.
- 16 AWG (1.5 mm²): up to 200 ft (60 m)
- 18 AWG (1 mm²): up to 125 ft (35 m)
- Two or three small shades sharing: 200 ft (60 m), 75 ft (20 m), 50 ft (15 m)
How many shades can share one power supply output?
Lutron document 045314 allows one drive per output of a QS link power supply. A smart panel output may carry two or three small Roller 64 shades, or two small Roller 100 shades.
Page 9 charts the shade areas that allow sharing. For a GRAFIK Eye QS, Lutron document 045314 points to its specification submittal for the device count.
How do I check that every shade is communicating on the link?
Lutron document 045314 uses link diagnostics mode, entered at a drive or at the smart panel. At a drive, hold Close 5 seconds and tap CCW.
At the smart panel, tap Open, hold Open 5 seconds, then repeat. Every treatment on the link wiggles; one that does not, or shows a red LED, needs its wiring checked.
Does a factory reset of the drive erase the limits?
No: Lutron document 045314 states that a drive reset clears all keypad assignments but leaves the open and close limits.
Can Sivoia QS shades be run from an infrared remote?
Yes: Lutron document 045314 states the treatments can take a QS IR Eye receiver and a hand-held infrared remote. That works with or without GRAFIK Eye QS.
The troubleshooting chart asks for line of sight within 30 ft of the receiver.
Other Sivoia QS installation guides
Installation guides for the same Sivoia QS system:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| 045520Basic Wiring and Setup Installation Guide | Roller 20 to 300 | B | Nov 2016 |
| 045488Roller Shades Installation Guide: QS Link Plug-In Power Supply, NEMA 5-15 Plug, 120 V to 240 V Input, 35 V Output | Roller 20 to 300 | B | Jul 2016 |
| 045604Roller Shades Installation Guide: QS Power Supply J-Box Mount | Roller 20 to 300 | A | |
| 3671692Roller Shades Installation Guide: Quick Programming Reference Card | Roller 20 to 300 | A | Jan 2010 |
Documents used with 045314
Lutron document 045520 is the Sivoia QS basic wiring and setup guide; 3671692 is the quick programming reference card. Lutron documents 045528, 045488 and 045604 are the smart panel, plug-in supply and junction box supply installation guides.
| Document | Type | Revision | Date |
|---|---|---|---|
| 085835Serena Open Roll Roller Shades Specification Submittal | Specification Submittal | A | Feb 2026 |
| 369612Pico Wireless Control Specification Submittal | Specification Submittal | Q | Jun 2025 |
| CAD Drawing: 30-Output Configurable Power Panel Enclosure (Power Modules Sold Separately), 35V Output, Elevation View (Front) | CAD Drawing | ||
| CAD Drawing: 30-Output Configurable Power Panel Enclosure (Power Modules Sold Separately), 35V Output, Plan View (Bottom) | CAD Drawing | ||
| 08533510-Output Smart Panel Specification Submittal | Specification Submittal | D | Apr 2020 |
| 08559230-Output Configurable Power Panel Enclosure (Power Modules sold separately), 35V Output Specification Submittal | Specification Submittal | B | Nov 2018 |
| Roller Shades Wiring Diagram: Multiple Shades per Single QS Smart Panel | Wiring Diagram | ||
| Roller Shades Wiring Diagram: One Shade per Single QS Smart Panel | Wiring Diagram | ||
| Revit Family: QS J-Box 35V Power Supply | Revit Family | ||
| Revit Family: QS Smart Power Panel, 30 Output | Revit Family |
Revisions of 045314
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| B | Jun 2014 | Current. The file on assets.lutron.com. Checked 15 Oct 2026. |
Not covered in 045314, and what to read next
Lutron document 045314 does not cover mounting the shades or installing the power supplies themselves.
Publisher and citation for document 045314
Lutron Electronics Co., Inc. publishes document 045314, Rev B, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 15 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Sivoia QS?
New Way supplies and installs Lutron Sivoia QS shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 045314 filled in.
