You searched and this document matched it.
See all results085346 · Specification Submittal · Rev E · Jul 2026 · English · PDF, 12 pages, 6.4 MB
Lutron Sivoia QS Roman Shades Specification Submittal (085346, rev E)
Lutron's specification submittal for the Roman shade fabrication kits: a Roller 64, 100 or 150 drive with a shade tube.
Lutron 085346 Rev E (July 2026), Sivoia QS Roman Shades Specification Submittal. https://assets.lutron.com/a/documents/085346.pdf, via https://newwaykl.com/resources/lutron/roman-shades/sivoia-qs/lutron-sivoia-qs-roman-shades-specification-submittal-085346/
About document 085346
Lutron document 085346, Rev E of July 2026, is the Roman shade fabrication kit specification submittal: width, lift capacity, power, torque, contents, bracket and headrail dimensions, drive selection, mounting and cable connection.
What submittal 085346 covers
Lutron document 085346 has these ten sections. Each link opens the PDF at that page in a new tab.
- Roman shade fabrication kits, opens in a new tab page 1
- Important safety notice on window cord standards, opens in a new tab page 1
- Kit dimensions, opens in a new tab page 2
- Electronic drive unit selection: identify the lift system, opens in a new tab page 3
- Direct lift: drive selection and lift weight, opens in a new tab page 4
- Indirect lift: drive selection and lift weight, opens in a new tab page 6
- Mounting the Roller 64 kit without headbox, opens in a new tab page 8
- Mounting the Roller 64 kit with a headbox, opens in a new tab page 9
- Mounting the Roller 100 and 150 kits, opens in a new tab page 11
- Leveling the tube and connecting the cables, opens in a new tab page 12
Specifications in 085346
Lutron document 085346 prints 58 values in the groups the document uses, each with the document's unit. A row names the catalog codes it applies to. The page link beside each group opens the PDF where the group starts.
Roman Roller 64 Kit
PDF page 1 of 085346, opens in a new tab- Compatibility
- Sivoia QS and Sivoia QS Wireless drives and controls
- Maximum shade width
- 109.5 in (2.78 m)
- Maximum lift capacity
- 11.7 lb (5.3 kg); lift cord or band routing may reduce it
- Input
- 24 to 36 V DC, 52 W
- Torque
- 10 in-lb (1.12 N·m)
- Warranty
- 8 year limited
Roman Roller 100 Kit
PDF page 1 of 085346, opens in a new tab- Compatibility
- Sivoia QS and Sivoia QS Wireless drives and controls
- Maximum shade width
- 145.25 in (3.68 m)
- Maximum lift capacity
- 17.9 lb (8.12 kg); lift cord or band routing may reduce it
- Input
- 24 to 36 V DC, 37 W
- Torque
- 25 in-lb (2.82 N·m)
- Warranty
- 8 year limited
Roman Roller 150 Kit
PDF page 1 of 085346, opens in a new tab- Compatibility
- Sivoia QS and Sivoia QS Wireless drives and controls
- Maximum shade width
- 145.25 in (3.68 m)
- Maximum lift capacity
- 23.5 lb (10.66 kg); lift cord or band routing may reduce it
- Input
- 24 to 36 V DC, 45 W
- Torque
- 33 in-lb (3.73 N·m)
- Warranty
- 8 year limited
Environment
PDF page 1 of 085346, opens in a new tab- Use
- Indoor use only
- Temperature
- 32 °F to 104 °F (0 °C to 40 °C)
- Relative humidity
- Below 90%, non-condensing
Kit Contents
PDF page 1 of 085346, opens in a new tab- Roller 64 kit
- (1) EDU-equipped shade tube with idler; (2) mounting brackets with screws; (1) 4-pin EDU terminal block and wire management bracket; (1) RF wireless receiver, wireless only; (1) headbox with endcaps, UK only
- Roller 100 and Roller 150 kits
- (1) EDU-equipped shade tube with idler; (2) mounting brackets with screws; (4) shade-to-mounting-bracket screws; (1) idler support bracket; (1) idler-adjust bracket; (1) 4-pin EDU terminal block and wire management bracket; (1) RF wireless receiver, wireless only
- Hook strip for the headbox
- Sold separately in 164 ft (50 m) rollsModels: WIN-RM-HOOK-50
Dimensions, Roller 64
PDF page 2 of 085346, opens in a new tab- Bracket-to-bracket width
- 17.5 in (445 mm) to 109.5 in (2781 mm)
- Minimum headrail-end to bracket clearance
- 0.125 in (3 mm)
- Bracket-to-tube gap
- 0.75 in (19 mm)
- Minimum headrail depth
- 2.50 in (64 mm)
- Bracket depth
- 1.50 in (38 mm)
- Bracket height
- 1.75 in (45 mm)
- Tube-to-headrail clearance
- 0.55 in (14 mm)
- Tube diameter (without fabric)
- 1.67 in (42 mm)
Dimensions, Roller 64 headbox (included in the UK)
PDF page 2 of 085346, opens in a new tab- Minimum headbox width (including endcaps)
- 17 21/32 in (448 mm)
- Headbox and endcaps depth
- 3 in (76 mm)
- Hook slot
- 0.9 in (23 mm)
Dimensions, Roller 100 and Roller 150
PDF page 2 of 085346, opens in a new tab- Bracket-to-bracket width
- 24 in (610 mm) to 145.25 in (3689 mm)
- Minimum headrail-end to bracket clearance
- 0.125 in (3 mm)
- Bracket-to-tube gap
- 0.625 in (16 mm)
- Minimum headrail depth
- 4.50 in (114 mm)
- Bracket depth
- 3.125 in (79 mm)
- Bracket height
- 3.50 in (89 mm)
- Tube-to-headrail clearance
- 0.72 in (18 mm)
- Tube diameter (without fabric)
- 2.56 in (65 mm)
- Fabric capacity graphs (Figures 2a and 3a)
- Fabric weight 5 to 50 oz/yd² (170 to 1695 gsm) against fabric size 5 to 144 ft² (0.465 to 13.378 m²)
- Direct lift, Roller 64
- 8.8 lb to 11.7 lb (3.99 kg to 5.31 kg) for H 0.75 in to 1.50 in (19.0 mm to 38.1 mm) and V from 1.26 in (31.8 mm)
- Direct lift, Roller 100
- 13.8 lb to 17.9 lb (6.26 kg to 8.12 kg) for H 1.25 in to 2.00 in (31.75 mm to 50.8 mm) and V from 1.51 in (38.2 mm)
- Direct lift, Roller 150
- 18.1 lb to 23.5 lb (8.21 kg to 10.66 kg) for H 1.25 in to 2.00 in (31.75 mm to 50.8 mm) and V from 1.51 in (38.2 mm)
- Indirect lift, Roller 64
- 6.5 lb to 7.8 lb (2.95 kg to 3.54 kg) for H from 0.75 in (19.0 mm) and V 0.00 in to 0.75 in (0.00 mm to 19.0 mm)
- Indirect lift, Roller 100
- 10.6 lb to 12.3 lb (4.81 kg to 5.58 kg) for H from 1.25 in (31.75 mm) and V 0.00 in to 0.75 in (0.00 mm to 19.0 mm)
- Indirect lift, Roller 150
- 13.9 lb to 16.2 lb (6.30 kg to 7.35 kg) for H from 1.25 in (31.75 mm) and V 0.00 in to 0.75 in (0.00 mm to 19.0 mm)
Mounting, Roller 64
PDF page 8 of 085346, opens in a new tab- Bracket mounting screws
- (2) per bracket, provided
- Structural support
- Blocking or other structural material supporting 300 lbs (136.1 kg)
- L brackets for a wall-mounted headrail
- Rated to support 300 lbs (136.1 kg)
Mounting, Roller 100 and Roller 150
PDF page 11 of 085346, opens in a new tab- Bracket mounting screws
- (3) per bracket, provided
- Structural support
- Blocking or other structural material supporting 450 lbs (204.1 kg)
- L brackets for a wall-mounted headrail
- Rated to support 450 lbs (204.1 kg)
- Drive end, (2) coarse-thread EDU mounting screws
- Torque 12 in-lb ±1 in-lb (1.36 N·m ±0.11 N·m)
- Idler end, (2) fine-thread idler mounting screws
- Torque 17 in-lb ±1 in-lb (1.92 N·m ±0.11 N·m)
Installation walk-through for 085346
Lutron document 085346 gives 14 steps, in the document's order, after the tools and fixings it lists.
The clearance, the check and the warning under a step are the document's own.
Tools
- Screwdriver
- Bubble level
Fixings
- (2) bracket mounting screws per bracket, Roller 64 (provided)
- (3) bracket mounting screws per bracket, Roller 100 and Roller 150 (provided)
- (2) coarse-thread EDU mounting screws, Roller 100 and 150 (provided)
- (2) fine-thread idler mounting screws, Roller 100 and 150 (provided)
- Cable tie and cable tie anchor (provided)
- Fasteners suited to the mounting surface, chosen by the installer
- Wall-mounted headrail L brackets: 300 lbs (136.1 kg), Roller 64
- Wall-mounted headrail L brackets: 450 lbs (204.1 kg), Roller 100 and 150
- Hook strip WIN-RM-HOOK-50 for the headbox, sold separately
Identify the lift system
Direct lift runs the lift cords from the top lift rings straight onto the tube, with no eye screws. Indirect lift passes them through an eye screw or guide on the headrail first.
Decide which applies. Direct lift continues in section 2 on page 4, indirect lift in section 3 on page 6.
Make a first choice from the fabric graph
Read fabric weight against fabric size on Figure 2a for direct lift or Figure 3a for indirect lift. The graph picks the Roller 64, Roller 100 or Roller 150.
A Roller 64 choice moves to the Roller 100 when the bracket-to-bracket width is over 109.5 in (2781 mm).
Clearance: 109.5 in (2781 mm) maximum bracket-to-bracket width for the Roller 64
Measure H and V
H is the horizontal distance from the tube center to the first lift ring eye or screw eye. V is the vertical distance from the headrail to the point where the cord touches that ring or screw eye.
Confirm the drive against combined lift weight
Look up the maximum allowable combined lift weight for the measured H and V in the chosen drive's table. Combined weight counts everything the drive lifts: lift rings, cords, bands, battens and hembar.
A load above the table moves the Roller 64 up to the Roller 100, and the 100 to the 150. Above the Roller 150 table the load must come down.
Check: The combined lift weight sits within the table value for the measured H and V.
Roller 64 without headbox: mount the brackets
Set the brackets on the underside of the headrail, bracket-to-bracket width apart, and fix each with the two screws provided.
Clearance: At least 0.125 in (3 mm) from each headrail end to the bracket
Warning: Wall mounting of the shade brackets is not recommended; a wall-mounted headrail needs L brackets rated for 300 lbs (136.1 kg).
Roller 64: fit the idler end
Hook the idler mounting yoke over and under the mounting tabs on the bracket, then tighten the securing screw.
Roller 64: fit the drive end
Turn the EDU mounting yoke so the drive control buttons face down. Lead the EDU cables through one of the side notches.
Push the tube against the spring-loaded idler for clearance. Seat the drive yoke over and under the bracket tabs and tighten the securing screw.
Check: The drive control buttons face downward.
Headbox: fit the hook strip and endcaps
Cut the hook strip to width and slide it into the headbox slot. Press the endcaps into both ends of the headbox, if used.
Headbox: mount the headbox and brackets
Place the brackets bracket-to-bracket width apart on the underside of the headbox for a ceiling mount. For a wall or face mount, place them on its inner back face.
Fix each bracket through the headbox into the substrate with the two screws provided, pre-drilling the headbox as Lutron recommends. The idler end and drive end then go in as for the headrail mount.
Warning: Blocking or other structural material must support 300 lbs (136.1 kg).
Roller 100 and 150: mount the brackets
Set the brackets on the underside of the headrail, bracket-to-bracket width apart, and fix each with the three screws provided.
Clearance: Bracket at least 0.125 in (3 mm) in from each headrail end
Warning: Wall mounting of the shade brackets is not recommended; a wall-mounted headrail needs L brackets rated for 450 lbs (204.1 kg).
Roller 100 and 150: assemble the idler brackets
With the idler adjusting screw head pointing down, slide the idler-adjust bracket behind the screw and the idler tabs. Then slide the idler-support bracket over and under the adjusting screw.
Turn the adjusting screw with a screwdriver until the holes in both brackets line up.
Check: The mounting holes of the idler-adjust and idler-support brackets align.
Roller 100 and 150: install the shade tube
Fix the drive end to its bracket with the two coarse-thread EDU mounting screws. Then fix the idler end with the two fine-thread idler mounting screws.
Clearance: Torque 12 in-lb ±1 in-lb (1.36 N·m ±0.11 N·m) at the drive end; 17 in-lb ±1 in-lb (1.92 N·m ±0.11 N·m) at the idler end
Roller 100 and 150: level the shade tube
Check the tube with a bubble level and correct it at the idler adjusting screw. Clockwise lowers the idler end of the tube, counter-clockwise raises it.
Check: The shade tube reads level on the bubble level.
All kits: connect and secure the EDU cables
Wire the 4-pin terminal block as Lutron document 045520 directs and plug in the EDU connector. Hold the connectors to the headrail with the wire management bracket.
Fit a wireless receiver where used, following Lutron document 045515. Tie the cables to the headrail with the cable tie and anchor provided.
Check: The cables cannot reach the moving parts of the finished shade.
Warning: Secure the cables where they will not interfere with the shade as it moves.
Facts Lutron states in 085346
The values Lutron document 085346 states, as published:
- Roller 64 kit
- Maximum shade width 109.5 in (2.78 m)
- Maximum lift capacity 11.7 lb (5.3 kg)
- Input 24 to 36 V DC at 52 W
- Torque 10 in-lb (1.12 N·m)
- Roller 100 kit
- Maximum shade width 145.25 in (3.68 m)
- Maximum lift capacity 17.9 lb (8.12 kg)
- Input 24 to 36 V DC at 37 W
- Torque 25 in-lb (2.82 N·m)
- Roller 150 kit
- Maximum shade width 145.25 in (3.68 m)
- Maximum lift capacity 23.5 lb (10.66 kg)
- Input 24 to 36 V DC at 45 W
- Torque 33 in-lb (3.73 N·m)
- Warranty and environment
- 8 year limited warranty on each kit
- Indoor use only, 32 °F to 104 °F (0 °C to 40 °C)
- Relative humidity below 90% non-condensing
- Kit contents
- EDU-equipped shade tube with idler
- Two brackets with their screws
- 4-pin EDU terminal block with wire management bracket
- RF wireless receiver, only with Sivoia QS wireless control
- Roller 100 and 150 kits add four shade-to-bracket screws
- Roller 100 and 150 kits add idler support and idler-adjust brackets
- Roller 64 headbox
- Headbox with endcaps included when shipping to the UK
- Minimum width with endcaps 17 21/32 in (448 mm)
- Depth 3 in (76 mm), hook slot 0.9 in (23 mm)
- Hook strip WIN-RM-HOOK-50 sold in 164 ft (50 m) rolls
- Headrail dimensions, Roller 64
- Bracket-to-bracket width 17.5 in (445 mm) to 109.5 in (2781 mm)
- Minimum headrail depth 2.50 in (64 mm)
- Tube-to-headrail clearance 0.55 in (14 mm)
- Bare tube diameter 1.67 in (42 mm)
- Headrail, Roller 100 and 150
- Bracket-to-bracket width 24 in (610 mm) to 145.25 in (3689 mm)
- Minimum headrail depth 4.50 in (114 mm)
- Tube-to-headrail clearance 0.72 in (18 mm)
- Bare tube diameter 2.56 in (65 mm)
- Headrail end clearance
- At least 0.125 in (3 mm) from each headrail end to the bracket, both bracket sizes
- Combined lift weight limits
- Direct lift (no eye screws) or indirect lift (through eye screws), exact figure depending on measured H and V
- Roller 64: 11.7 lb (5.31 kg) direct lift, 7.8 lb (3.54 kg) indirect
- Roller 100: 17.9 lb (8.12 kg) direct lift, 12.3 lb (5.58 kg) indirect
- Roller 150: 23.5 lb (10.66 kg) direct lift, 16.2 lb (7.35 kg) indirect
- Mounting load
- Blocking able to support the kit, with wall-mounting of the shade brackets not recommended
- Roller 64 kits: 300 lb (136.1 kg)
- Roller 100 and 150 kits: 450 lb (204.1 kg)
- Torque, Roller 100 and 150
- Drive end: 2 coarse-thread EDU screws at 12 in-lb ±1 in-lb (1.36 N·m ±0.11 N·m)
- Idler end: 2 fine-thread idler screws at 17 in-lb ±1 in-lb (1.92 N·m ±0.11 N·m)
Questions about document 085346
The answers come from Lutron document 085346 and New Way's record of it.
What is Lutron document 085346?
Lutron's 12-page Roman kit submittal dated 22 July 2026, for custom Roman shades on Sivoia QS or Sivoia QS Wireless.
Which revision of 085346 is current?
Rev E, dated July 2026, is the revision Lutron publishes. New Way checked it against assets.lutron.com on 15 October 2026.
Which roman shades does 085346 cover?
Lutron Sivoia QS roman shades. For related steps Lutron refers readers to document 045520.
How is the right drive chosen for a Roman shade?
Lutron document 085346 first asks whether the lift cords wrap straight onto the tube or pass through eye screws.
- A fabric weight and size graph gives a first choice
- Combined lift weight tables for the measured H and V confirm it
- A load above the table moves the choice up a drive
How wide and how heavy can each kit go?
Lutron document 085346 rates each kit by maximum width and lift capacity, which the cord or band routing can reduce.
- Roller 64: 109.5 in (2.78 m) and 11.7 lb (5.3 kg)
- Roller 100: 145.25 in (3.68 m) and 17.9 lb (8.12 kg)
- Roller 150: 145.25 in (3.68 m) and 23.5 lb (10.66 kg)
How deep must the headrail be?
Lutron document 085346 gives a minimum headrail depth of 2.50 in (64 mm) for the Roller 64 kit.
- Roller 100 and 150 kits: 4.50 in (114 mm)
- 0.125 in (3 mm) clearance from each headrail end to the bracket
What must the mounting structure carry?
Lutron document 085346 requires blocking or other structural material, with fasteners chosen by the installer for the substrate.
- Roller 64 kit: 300 lb (136.1 kg)
- Roller 100 or Roller 150 kit: 450 lb (204.1 kg)
Which torque goes on the Roller 100 and Roller 150 shade screws?
Lutron document 085346 fixes the drive end with two coarse-thread EDU mounting screws at 12 in-lb ±1 in-lb (1.36 N·m ±0.11 N·m). The idler end takes two fine-thread idler mounting screws at 17 in-lb ±1 in-lb (1.92 N·m ±0.11 N·m).
Other Sivoia QS specification submittals
Specification submittals for the same Sivoia QS system:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| 085762Triathlon Roman Shades Specification Submittal | C | May 2024 |
Documents used with 085346
Lutron document 085762 is the specification submittal for the Triathlon and Serena Roman shade fabrication kit. Lutron serves the receiver guide as 045515, which prints 045555, the number the library uses.
| Document | Type | Revision | Date |
|---|---|---|---|
| 045520Basic Wiring and Setup Installation Guide | Installation Guide | B | Nov 2016 |
| 045555Installation Guide: Wireless RF Receiver, Basic Wiring and Setup | Installation Guide | B | Oct 2016 |
| CAD Drawing: Shade Equipment CAD Block | CAD Drawing | ||
| Roman Shades CAD Drawing: Roller 64 Roman Bracket, Fabrication Kit | CAD Drawing | A | |
| 048846Application Note: EU EcoDesign Standby Power Information | Application Note | A | Nov 2024 |
| Application Note: Blink Codes for Shades and Venetian Blinds | Application Note | ||
| 3671319Product Brochure: Residential Shading Solutions | Product Brochure | K | Feb 2023 |
| 122400Performance Specification: Section 122400, Window Shades | Performance Specification |
Revisions of 085346
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| E | Jul 2026 | Current. The file on assets.lutron.com. Checked 15 Oct 2026. |
Not covered in 085346, and what to read next
Lutron document 085346 leaves the wiring of the 4-pin terminal block and the wireless receiver to other guides.
Publisher and citation for document 085346
Lutron Electronics Co., Inc. publishes document 085346, Rev E, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 15 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Sivoia QS?
New Way supplies and installs Lutron Sivoia QS shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 085346 filled in.
