You searched and this document matched it.
See all resultsCAD Drawing · Rev A · English · PDF, DWG, DXF
Lutron Sivoia QS Tension Shades and Skylights CAD Drawing: Bottom-Up Angled Inside-Mount Recessed Mount, Section View
Lutron's tensioned roller detail of the Sivoia QS bottom-up shade in an angled inside mount, a 1/4 scale typical section.
Lutron, Sivoia QS Tension Shades and Skylights CAD Drawing: Bottom-Up Angled Inside-Mount Recessed Mount, Section View. https://assets.lutron.com/a/documents/0115-butr-ctm-s.pdf, via https://newwaykl.com/resources/lutron/tension-shades-and-skylights/sivoia-qs/lutron-sivoia-qs-tension-shades-and-skylights-cad-drawing-bottom-up-angled-inside-mount-recessed-mount-section-view/
About this Sivoia QS drawing
Lutron drawing 0115-BUTR-CTM-S, revision A, is a section beside the glazing with caulking or finish trim labeled, a 36 in (914 mm) minimum well length, an install angle inset and an inside mount deduction note.
What this Sivoia QS drawing covers
This Sivoia QS drawing has these eleven sections.
- Header band: tensioned roller detail, scale 1/4
- Code 0115-BUTR-CTM-S in the header band
- Inset: maximum bottom-up install angles, 45 degrees
- View 1, typical section at scale 1/4
- Bottom-up shade in an angled inside mount
- Labeled parts: glazing, caulking or finish trim
- Skylight well length, 36 in (914 mm) minimum
- Two asterisked and three unmarked dimensions
- Note: inside mount deduction, 1/8 in all sides
- Title block: bottom-up, angled inside mount (section)
- Drawing number line blank, revision A, 2009 copyright
Specifications in this Sivoia QS drawing
This Sivoia QS drawing prints ten values in the groups the document uses, each with the document's unit. The page link beside each group opens the PDF where the group starts.
- Maximum bottom-up install angle, each side of the vertical line
- 45 degrees
- Skylight well length, minimum
- 36Â in (914Â mm)
- Marked with an asterisk, near the top of the sheet
- 0.13Â in (3Â mm)
- Near the top of the sheet
- 2.25Â in (57Â mm)
- At the middle of the section
- 4.75Â in (121Â mm)
- Near the bottom of the sheet
- 4.64Â in (118Â mm)
- Marked with an asterisk, near the bottom of the sheet
- 0.13Â in (3Â mm)
- Deduction for inside mount, all sides
- 1/8Â in
- Scale
- 1/4
- Revision
- A
Facts Lutron states in this Sivoia QS drawing
The values this Sivoia QS drawing states, as published:
- Drawing code and revision
- 0115-BUTR-CTM-S in the header band and revision A in the title block, with the drawing number line blank
- Sheet title
- Bottom-up, angled inside mount (section), under the header tensioned roller detail
- Scale
- 1/4, printed in the header band and under view 1
- Maximum bottom-up install angles
- 45 degrees on each side of a vertical line, drawn in an inset
- Skylight well length
- 36Â in (914Â mm) minimum, marked along the shade
- Inside mount deduction
- 1/8Â in on all sides by the sheet's note, with the two asterisked dimensions reading 0.13Â in (3Â mm)
- Unlabeled dimensions
- 2.25Â in (57Â mm) near the top of the sheet
- 4.75Â in (121Â mm) at the middle of the section
- 4.64Â in (118Â mm) near the bottom of the sheet
- Labeled parts
- Glazing, and caulking or finish trim at two points
- File formats
- PDF (one page, about 128 KB), DWG and DXF
- Date
- Copyright 2009, no issue date
Questions about this Sivoia QS drawing
The answers come from this Sivoia QS drawing and New Way's record of it.
What is this Sivoia QS drawing?
Lutron's tensioned roller detail of the Sivoia QS bottom-up shade in an angled inside mount, a 1/4 scale typical section. Lutron drawing 0115-BUTR-CTM-S, revision A, is a section beside the glazing with caulking or finish trim labeled, a 36 in (914 mm) minimum well length, an install angle inset and an inside mount deduction note.
Which revision of this Sivoia QS drawing is current?
Rev A is the revision Lutron publishes. New Way checked it against assets.lutron.com on 16 October 2026.
Which tension shades and skylights does this Sivoia QS drawing cover?
Lutron Sivoia QS tension shades and skylights.
What does Lutron drawing 0115-BUTR-CTM-S show?
Lutron's section sets the bottom-up shade at an angle beside the glazing, with caulking or finish trim labeled. Lutron adds an inset of the maximum install angles and prints five dimensions.
What is the maximum bottom-up install angle?
Lutron's inset, headed maximum bottom-up install angles, draws the shade at 45 degrees on each side of a vertical line.
What deduction does the angled inside mount take?
Lutron's note calls for a deduction of 1/8 in on all sides for the inside mount. The two dimensions marked with the same asterisk read 0.13 in (3 mm).
What minimum length does the drawing give?
Lutron marks the skylight well length with a minimum of 36 in (914 mm) on drawing 0115-BUTR-CTM-S; no maximum is printed.
Which documents go with this Sivoia QS drawing?
Three documents go with this Sivoia QS drawing, listed under Documents used with this Sivoia QS drawing with the others:
Other Sivoia QS CAD drawings
CAD drawings for the same Sivoia QS system:
All 15 Sivoia QS CAD drawingsDocuments used with this Sivoia QS drawing
Lutron draws the bottom-up inside mount without the angle as 0098-BUTR-IMT-S (section) and 0099-BUTR-IMT-F (elevation). Lutron drawing 101-SKTR-CTM-S is the angled skylight inside mount (length), 045156 the installation guide and 086130 the specification submittal.
| Document | Type | Revision | Date |
|---|---|---|---|
| 045156Tension Shades and Skylights Installation Guide | Installation Guide | B | |
| 086130Tension Shades and Skylights Specification Submittal | Specification Submittal | A | Feb 2026 |
| 048846Application Note: EU EcoDesign Standby Power Information | Application Note | A | Nov 2024 |
| 3671530Tension Shades and Skylights Product Brochure: Tensioned Roller Shades | Product Brochure | I | May 2016 |
| 3683231Application Note: Care and Maintenance of Window Treatments | Application Note | C | |
| Performance Specification: Section 086710, Skylight Shades | Performance Specification | ||
| 3671319Product Brochure: Residential Shading Solutions | Product Brochure | K | Feb 2023 |
Revisions of this Sivoia QS drawing
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| A | Not stated | Current. The file on assets.lutron.com. Checked 16 Oct 2026. |
Not covered in this Sivoia QS drawing, and what to read next
Lutron drawing 0115-BUTR-CTM-S shows one section: no elevation, no fixing size, no wiring and no mounting steps.
- Elevation: 0099-BUTR-IMT-F, the bottom-up inside mount elevation view
- Mounting: 045156, the tension shades and skylights installation guide
Publisher and citation for this Sivoia QS drawing
Lutron Electronics Co., Inc. publishes this document and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 16 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Sivoia QS?
New Way supplies and installs Lutron Sivoia QS shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
