You searched and this document matched it.
See all resultsCAD Drawing · Rev A · English · PDF, 1 page, 0.2 MB
Lutron Manual Clutch CAD Drawing: V16, Dual Wall-Mount (Section)
Lutron's roller shade detail drawing of the V16 manual roller clutch in a dual wall mount, at scale 1/2.
Lutron, Manual Clutch CAD Drawing: V16, Dual Wall-Mount. https://assets.lutron.com/a/documents/0187-v16m-dwm-s.pdf, via https://newwaykl.com/resources/lutron/roller-shades/manual/lutron-manual-clutch-cad-drawing-v16-dual-wall-mount-section/
About this Manual drawing
Lutron drawing 0187-V16M-DWM-S, revision A, is a one-page CAD drawing: a typical section of two V16 clutch units on one mounting plate against a wall, an isometric view, a maximum roll diameter and six dimensions.
What this Manual drawing covers
This Manual drawing has these six sections.
- Title block: drawing number, revision and scale
- View 1: section, two clutches against a wall
- Maximum roll diameter on both rollers
- Three vertical, three horizontal dimensions, unlabeled
- Note beside the chain: always use tension device
- View 2: isometric view, not to scale
Specifications in this Manual drawing
This Manual drawing prints ten values in the groups the document uses, each with the document's unit. The page link beside each group opens the PDF where the group starts.
- MAX ROLL DIA, upper roller
- 3.5 in (79 mm)
- MAX ROLL DIA, lower roller
- 3.5 in (79 mm)
- horizontal dimension above the section
- 6.5 in (165 mm)
- vertical dimension, far left of the section
- 6.5 in (165 mm)
- upper vertical dimension, inner line at the left
- 2.1 in (53 mm)
- lower vertical dimension, inner line at the left
- 3.1 in (79 mm)
- horizontal dimension below the section, left
- 2.9 in (74 mm)
- horizontal dimension below the section, right
- 2.2 in (56 mm)
- Scale
- 1/2
- Scale
- not to scale
Facts Lutron states in this Manual drawing
The values this Manual drawing states, as published:
- Drawing number and revision
- 0187-V16M-DWM-S, revision A, printed in the title block
- Sheet title
- Roller shade detail drawing, V16 manual roller, dual wall mount
- Scale, view 1
- 1/2 for the typical section
- Scale, view 2
- Isometric view, not to scale
- Maximum roll diameter
- 3.5 in (79 mm), labeled MAX ROLL DIA on each of the two rollers, as printed
- Vertical dimensions, view 1
- 6.5 in (165 mm) at the far left of the section
- 2.1 in (53 mm) on the inner line at the left, upper
- 3.1 in (79 mm) on the inner line at the left, lower
- Horizontal dimensions, view 1
- 6.5 in (165 mm) above the section
- 2.9 in (74 mm) below the section, left
- 2.2 in (56 mm) below the section, right
- Note on the sheet
- Always use tension device, printed beside the chain in view 1
- File format
- PDF only (one page, about 175 KB), no DWG or DXF listed for this sheet
- Copyright and date
- Copyright 2010 in the title block, no issue date
Questions about this Manual drawing
The answers come from this Manual drawing and New Way's record of it.
What is Lutron drawing 0187-V16M-DWM-S?
Lutron's sheet draws the two clutches one above the other against a hatched wall at the right.
Each clutch has a chain loop below it. The title block carries a 2010 copyright line and no issue date.
Which revision of this Manual drawing is current?
Rev A is the revision Lutron publishes. New Way checked it against assets.lutron.com on 16 October 2026.
Which roller shades does this Manual drawing cover?
Lutron Manual roller shades in the Clutch drive class.
What maximum roll diameter does the dual wall mount sheet print?
Lutron prints 3.5 in (79 mm) MAX ROLL DIA on both rollers of the dual wall mount section. No other diameter is given on the sheet.
Which dimensions does the section carry?
Lutron's section carries six unlabeled dimensions, the largest 6.5 in (165 mm) above it and again at its far left.
- Inner line at the left: 2.1 in (53 mm) and 3.1 in (79 mm)
- Below the section: 2.9 in (74 mm) and 2.2 in (56 mm)
Which file formats does Lutron supply for the dual wall mount section?
Lutron's download for drawing 0187-V16M-DWM-S is a one-page PDF of about 175 KB. No DWG or DXF file is listed for this sheet.
Which documents go with this Manual drawing?
Three documents go with this Manual drawing, listed under Documents used with this Manual drawing:
Other Manual Clutch CAD drawings
CAD drawings for the same Manual Clutch drive class:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| Clutch CAD Drawing: V16, Dual Ceiling-Mount (Section) | Clutch | A | |
| Clutch CAD Drawing: V16, 3″ Fascia Mount (Section) | Clutch | A | |
| Clutch CAD Drawing: V16, 4″ Fascia Mount (Section) | Clutch | A | |
| Clutch CAD Drawing: V16, 4.75″ Pocket Mount (Section) | Clutch | A |
Documents used with this Manual drawing
Lutron drawing 0188-V16M-DCM-S is the matching V16 dual ceiling mount section, beside the V16 fascia and pocket mount drawings. Lutron document 085608 is the manual clutch specification submittal and 045971 the installation guide.
| Document | Type | Revision | Date |
|---|---|---|---|
| 085608Clutch Specification Submittal | Specification Submittal | B | Apr 2024 |
| 045971Sivoia QS Manual Clutch Shade Installation Guide | Installation Guide | A | Apr 2024 |
| 048863Sivoia QS Roller Shades Application Note: Fabric Aesthetic Characteristics | Application Note | A | May 2026 |
Revisions of this Manual drawing
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| A | Not stated | Current. The file on assets.lutron.com. Checked 16 Oct 2026. |
Not covered in this Manual drawing, and what to read next
Lutron drawing 0187-V16M-DWM-S shows the wall mount and clutches only: no fascia, pocket, fabric width, chain drop or fixing size.
- Ceiling mount: 0188-V16M-DCM-S, the V16 dual ceiling mount CAD drawing
- Mounting steps: 045971, the manual clutch shade installation guide
Publisher and citation for this Manual drawing
Lutron Electronics Co., Inc. publishes this document and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 16 October 2026.
Lutron is a trademark of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Manual roller shades?
New Way supplies and installs Lutron Manual roller shades in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
