You searched and this document matched it.
See all resultsCAD Drawing · Rev A · English · PDF, DWG, DXF
Lutron Manual Clutch CAD Drawing: V24, 4.75″ Pocket Mount (Section)
Lutron's roller shade detail drawing of the V24 manual roller clutch in a 4.75 in pocket mount, at full size.
Lutron, Manual Clutch CAD Drawing: V24, 4.75 in. Pocket Mount. https://assets.lutron.com/a/documents/0201-v24m-pmt-s.pdf, via https://newwaykl.com/resources/lutron/roller-shades/manual/lutron-manual-clutch-cad-drawing-v24-4-75-pocket-mount-section/
About this Manual drawing
Lutron drawing 0201-V24M-PMT-S, revision A, is a one-page CAD drawing: a typical section at scale 1/1 of the V24 clutch on a slotted mounting plate inside a pocket, a maximum roll diameter and five dimensions.
What this Manual drawing covers
This Manual drawing has these six sections.
- Title block: drawing number, revision and scale
- View 1: section, the clutch inside a pocket
- Maximum roll diameter, a labeled dashed circle
- Two dimensions above, one at the right, unlabeled
- Lower left and below: two unlabeled dimensions
- Part label on the section: V24 CLUTCH
Specifications in this Manual drawing
This Manual drawing prints seven values in the groups the document uses, each with the document's unit. The page link beside each group opens the PDF where the group starts.
- MAX ROLL DIA
- 3.5 in (89 mm)
- horizontal dimension above the section, upper line
- 4.75 in (121 mm)
- horizontal dimension above the section, lower line, at the left
- 1.02 in (26 mm)
- vertical dimension, right of the section
- 5.00 in (127 mm)
- horizontal dimension, lower left of the section
- 0.52 in (13 mm)
- horizontal dimension below the section
- 3.00 in (76 mm)
- Scale
- 1/1
Facts Lutron states in this Manual drawing
The values this Manual drawing states, as published:
- Drawing number and revision
- 0201-V24M-PMT-S, revision A, printed in the title block
- Sheet title
- Roller shade detail drawing, V24 manual roller, 4.75 in pocket mount
- Scale
- 1/1 (full size), printed in the title block and under view 1
- Maximum roll diameter
- 3.5 in (89 mm), labeled MAX ROLL DIA on a dashed circle
- Dimensions above the section
- 4.75 in (121 mm) on the upper line and 1.02 in (26 mm) on the lower line, at the left
- Dimension, right of section
- 5.00 in (127 mm)
- Dimensions, lower left and below
- 0.52 in (13 mm) at the lower left and 3.00 in (76 mm) below
- Part labeled
- V24 CLUTCH, with a leader to the clutch body
- File formats
- PDF (one page, about 101 KB), DWG and DXF
- Copyright and date
- Copyright 2010 in the title block, no issue date
Questions about this Manual drawing
The answers come from this Manual drawing and New Way's record of it.
What is Lutron drawing 0201-V24M-PMT-S?
Lutron's sheet hatches the pocket across its top and down both sides.
A closure runs along the bottom at the right. The title block carries a 2010 copyright line and no issue date.
Which revision of this Manual drawing is current?
Rev A is the revision Lutron publishes. New Way checked it against assets.lutron.com on 16 October 2026.
Which roller shades does this Manual drawing cover?
Lutron Manual roller shades in the Clutch drive class.
What maximum roll diameter does the pocket section print?
Lutron prints 3.5 in (89 mm) MAX ROLL DIA on a dashed circle around the roller in the pocket section. No other diameter is given on the sheet.
Which dimensions does the pocket section carry?
Lutron's section carries five unlabeled dimensions, the largest 5.00 in (127 mm) at its right.
- Above the section: 4.75 in (121 mm) and 1.02 in (26 mm)
- Lower left: 0.52 in (13 mm)
- Below the section: 3.00 in (76 mm)
Which file formats does Lutron offer for the pocket section?
Lutron publishes drawing 0201-V24M-PMT-S as a PDF of about 101 KB and as DWG and DXF files for CAD programs.
Which documents go with this Manual drawing?
Three documents go with this Manual drawing, listed under Documents used with this Manual drawing:
Other Manual Clutch CAD drawings
CAD drawings for the same Manual Clutch drive class:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| Clutch CAD Drawing: V16, 4.75″ Pocket Mount (Section) | Clutch | A | |
| Clutch CAD Drawing: V16, 3″ Fascia Mount (Section) | Clutch | A | |
| Clutch CAD Drawing: V16, 4″ Fascia Mount (Section) | Clutch | A | |
| Clutch CAD Drawing: V16, Dual Ceiling-Mount (Section) | Clutch | A |
Documents used with this Manual drawing
Lutron drawing 0197-V24M-SFM-S is the matching V24 fascia mount section; the V16 pocket mount drawing is its V16 counterpart. Lutron document 085608 is the manual clutch specification submittal and 045971 the installation guide.
| Document | Type | Revision | Date |
|---|---|---|---|
| 085608Clutch Specification Submittal | Specification Submittal | B | Apr 2024 |
| 045971Sivoia QS Manual Clutch Shade Installation Guide | Installation Guide | A | Apr 2024 |
| 048863Sivoia QS Roller Shades Application Note: Fabric Aesthetic Characteristics | Application Note | A | May 2026 |
Revisions of this Manual drawing
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| A | Not stated | Current. The file on assets.lutron.com. Checked 16 Oct 2026. |
Not covered in this Manual drawing, and what to read next
Lutron drawing 0201-V24M-PMT-S shows the pocket section alone: no fascia, fabric width or drop, chain or plate fixing size.
- Fascia alternative: 0197-V24M-SFM-S, the V24 fascia mount CAD drawing
- Mounting steps: 045971, the manual clutch shade installation guide
Publisher and citation for this Manual drawing
Lutron Electronics Co., Inc. publishes this document and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 16 October 2026.
Lutron is a trademark of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Manual roller shades?
New Way supplies and installs Lutron Manual roller shades in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
