You searched and this document matched it.
See all resultsCAD Drawing · Rev A · English · PDF, DWG, DXF
Lutron Manual Clutch CAD Drawing: V8, 3″ Fascia Mount (Section)
Lutron's roller shade detail drawing of the V8 manual roller clutch in a 3 in fascia mount, at full size.
Lutron, Manual Clutch CAD Drawing: V8, 3 in. Fascia Mount. https://assets.lutron.com/a/documents/0165-v08m-sfm-s.pdf, via https://newwaykl.com/resources/lutron/roller-shades/manual/lutron-manual-clutch-cad-drawing-v8-3-fascia-mount-section/
About this Manual drawing
Lutron drawing 0165-V08M-SFM-S, revision A, is a one-page CAD drawing: a typical section at scale 1/1 of the V8 clutch inside a square fascia profile, one roller tube, a maximum roll and four dimensions.
What this Manual drawing covers
This Manual drawing has these six sections.
- Title block: drawing number, revision and scale
- View 1: section, the clutch inside a fascia
- Maximum roll, a labeled dashed circle
- One roller tube, labeled: S8 steel tube
- Two dimensions above, two at the right, unlabeled
- Part labels: V8 Clutch and hembar (varies)
Specifications in this Manual drawing
This Manual drawing prints seven values in the groups the document uses, each with the document's unit. The page link beside each group opens the PDF where the group starts.
- Max Roll
- Ø2.6 in (67 mm)
- S8 Steel Tube
- 1.0 in (25 mm)
- horizontal dimension above the section, upper line
- 3.1 in (79 mm)
- horizontal dimension above the section, lower line
- 3.0 in (76 mm)
- vertical dimension, right of the section, inner line
- 3.0 in (76 mm)
- vertical dimension, right of the section, outer line
- 3.1 in (79 mm)
- Scale
- 1/1
Facts Lutron states in this Manual drawing
The values this Manual drawing states, as published:
- Drawing number and revision
- 0165-V08M-SFM-S, revision A, printed in the title block
- Sheet title
- Roller shade detail drawing, V8 manual roller, 3-inch fascia mount
- Scale
- 1/1 (full size), printed in the title block and under view 1
- Maximum roll
- 2.6 in (67 mm) diameter, labeled Max Roll on a dashed circle
- Tube labeled
- S8 steel tube 1.0 in (25 mm)
- Dimensions above the section
- 3.1 in (79 mm) on the upper line and 3.0 in (76 mm) on the lower line
- Dimensions at the right
- 3.0 in (76 mm) on the inner line and 3.1 in (79 mm) on the outer line
- Part label, clutch
- V8 Clutch, with a leader to the clutch
- Part label, hembar
- HEMBAR (VARIES), with a leader to the hembar below the fascia
- File formats
- PDF (one page, about 105 KB), DWG and DXF
- Copyright and date
- Copyright 2010 in the title block, no issue date
Questions about this Manual drawing
The answers come from this Manual drawing and New Way's record of it.
What is Lutron drawing 0165-V08M-SFM-S?
Lutron's sheet labels the clutch and draws the one tube as a circle inside the fascia.
The title block carries a 2010 copyright line and no issue date.
Which revision of this Manual drawing is current?
Rev A is the revision Lutron publishes. New Way checked it against assets.lutron.com on 16 October 2026.
Which roller shades does this Manual drawing cover?
Lutron Manual roller shades in the Clutch drive class.
Which roller tube does the V8 fascia section draw?
Lutron draws one tube and labels it S8 steel tube 1.0 in (25 mm). No other tube size is printed on the sheet.
Which dimensions does the fascia section carry?
Lutron's section carries four unlabeled dimensions, the largest 3.1 in (79 mm) above it and again at its right.
- Above the section: 3.1 in (79 mm) and 3.0 in (76 mm)
- Right of the section: 3.0 in (76 mm) inner, 3.1 in (79 mm) outer
Does the sheet fix the hembar?
Lutron labels the hembar below the fascia "HEMBAR (VARIES)" and prints no hembar size.
Which documents go with this Manual drawing?
Three documents go with this Manual drawing, listed under Documents used with this Manual drawing:
Other Manual Clutch CAD drawings
CAD drawings for the same Manual Clutch drive class:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| Clutch CAD Drawing: V16, 3″ Fascia Mount (Section) | Clutch | A | |
| Clutch CAD Drawing: V16, 4″ Fascia Mount (Section) | Clutch | A | |
| Clutch CAD Drawing: V24, 4″ Fascia Mount (Section) | Clutch | A | |
| Clutch CAD Drawing: V16, 4.75″ Pocket Mount (Section) | Clutch | A |
Documents used with this Manual drawing
Lutron drawing 0165-V08M-SFM-S is the only V8 sheet; the matching fascia sections are two V16 drawings and 0197-V24M-SFM-S. Lutron document 085608 is the manual clutch specification submittal and 045973 the fascia installation guide.
| Document | Type | Revision | Date |
|---|---|---|---|
| 085608Clutch Specification Submittal | Specification Submittal | B | Apr 2024 |
| 045973Sivoia QS Manual Clutch Shade with Fascia Installation Guide | Installation Guide | A | Apr 2024 |
| 048863Sivoia QS Roller Shades Application Note: Fabric Aesthetic Characteristics | Application Note | A | May 2026 |
Revisions of this Manual drawing
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| A | Not stated | Current. The file on assets.lutron.com. Checked 16 Oct 2026. |
Not covered in this Manual drawing, and what to read next
Lutron drawing 0165-V08M-SFM-S shows the fascia section only: no pocket or ceiling mount, fabric size, chain, hembar or fixing sizes.
- V24 fascia: 0197-V24M-SFM-S, the V24 fascia mount CAD drawing
- Mounting steps: 045973, the manual clutch shade with fascia installation guide
Publisher and citation for this Manual drawing
Lutron Electronics Co., Inc. publishes this document and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 16 October 2026.
Lutron is a trademark of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Manual roller shades?
New Way supplies and installs Lutron Manual roller shades in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
