You searched and this document matched it.
See all results045625 · Installation Guide · Rev A · Jul 2018 · English, French, Spanish · PDF, 6 pages, 7.3 MB
Lutron Sivoia QS Roller Shades Installation Guide: Roller 100/150/300, Ceiling Mount Chassis (045625, rev A)
Lutron's chassis mounting guide for Roller 100, 150 and 300 shades on a wall, ceiling or jamb without a fascia.
Lutron 045625 Rev A (July 2018), Sivoia QS Roller Shades Installation Guide: Roller 100/150/300, Ceiling Mount Chassis. https://assets.lutron.com/a/documents/045625.pdf, via https://newwaykl.com/resources/lutron/roller-shades/sivoia-qs/lutron-sivoia-qs-roller-shades-installation-guide-045625/
About document 045625
Lutron document 045625, Rev A of July 2018, is the wall, ceiling and jamb mount chassis installation guide: sub-bracket marking and fixing, cable entry, hanging, leveling, wiring and care, in English, French and Spanish.
What guide 045625 covers
Lutron document 045625 has these eight sections. Each link opens the PDF at that page in a new tab.
- Prepare to install: notes, items and tools, opens in a new tab page 1
- Mark the sub-bracket locations, opens in a new tab page 1
- Install the sub-brackets, opens in a new tab page 1
- Cable entry for ceiling, wall and universal sub-brackets, opens in a new tab page 1
- Hang the shade: ceiling, wall and universal mount, opens in a new tab page 1
- Level the shade, opens in a new tab page 2
- Wire the shade and power up, opens in a new tab page 2
- Care and maintenance, opens in a new tab page 2
Specifications in 045625
Lutron document 045625 prints 19 values in the groups the document uses, each with the document's unit. The page link beside each group opens the PDF where the group starts.
Important notes
PDF page 1 of 045625, opens in a new tab- Ambient operating temperature
- 32 °F to 104 °F (0 °C to 40 °C)
- Humidity
- 0 to 90%, non-condensing
- Location
- Indoor use only
- Wiring and programming reference
- Sivoia QS Basic Wiring and Setup, P/N 045520
Tools required
PDF page 1 of 045625, opens in a new tab- Hex-head driver
- 1/4 in (6 mm)
Mark the sub-bracket locations
PDF page 1 of 045625, opens in a new tab- Bracket-to-bracket distance
- Tube width + 1.5 in (38 mm)
- Spacer blocks for wall mount
- May be required to clear the trim (not included)
Install the sub-brackets
PDF page 1 of 045625, opens in a new tab- Ceiling-mount screws per sub-bracket
- 4
- Wall-mount screws per sub-bracket
- 4
- Jamb-mount screws per sub-bracket
- 3
- Combination-mount screws per sub-bracket
- As many as the location allows, 4 minimum
- Supplied mounting screws
- Self-drilling, for solid wood structural members
- Universal sub-bracket orientation
- Only as shown
- People needed
- 2, one supporting each end
Cable entry
PDF page 1 of 045625, opens in a new tab- Cable exit
- Wall, ceiling or jamb, drive side
- Cable left exposed
- 12 to 18 in (30 to 45 cm)
- Ceiling sub-bracket
- Clearance hole for ceiling cable entry
- Universal sub-bracket
- Clearance holes for ceiling and wall cable entry
Level the shade
PDF page 2 of 045625, opens in a new tab- Idler adjusting screw
- Clockwise lowers, counter-clockwise raises the idler end
Installation walk-through for 045625
Lutron document 045625 gives eight steps, in the document's order, after the tools and fixings it lists.
The clearance, the check and the warning under a step are the document's own.
Tools
- 1/4 in (6 mm) hex-head driver
- #2 Phillips screwdriver
- Tape measure
- Power drill
- Level
Fixings
- Self-drilling mounting screws, supplied in each sub-bracket kit
- Supplied screws: for solid wood structural members
- Cable tie and anchor (in each sub-bracket kit)
- Installer-chosen fasteners for other surfaces, able to carry the operating load
- Spacer blocks for a wall mount where needed (not included)
Prepare
Read the important notes and check the shades, with shade brackets fitted, and the sub-bracket kits.
Check: Kits and tools present
Mark the sub-bracket locations
Mark the positions level and centered over the window, where the screws reach a structural member. Leave clearance so the fabric cannot rub trim, window or top treatment.
Clearance: Tube width + 1.5 in (38 mm)
Check: Marks level and centered
Install the sub-brackets
Fix the sub-brackets at the marks with fasteners suited to the surface.
Use 4 screws per ceiling or wall sub-bracket, or 4 on a universal sub-bracket for a ceiling or wall mount. A universal sub-bracket takes 3 for a jamb mount and at least 4 for a combination mount.
Clearance: 4 screws ceiling or wall, 3 jamb, at least 4 combination
Check: Fasteners carry the operating load
Warning: Supplied screws suit solid wood structural members; the universal sub-bracket mounts only in the orientation shown
Plan the cable entry
Bring the cable out on the drive side with 12 to 18 in (30 to 45 cm) exposed. Choose an entry point that does not clash with the sub-bracket.
Clearance: 12 to 18 in (30 to 45 cm)
Check: Cable cannot touch the moving fabric
Hang the shade
With one person at each end, hook the shade brackets into the sub-brackets. On a ceiling mount the top tab goes into the rear hook and the front over the front hook.
On a wall or universal mount, tilt the shade onto the upper tab and swing down onto the lower tab. Center the shade and fully tighten each securing screw with a hand screwdriver.
Check: Each bracket passes a careful tug
Warning: Two people, one supporting each end. 2 ladders or lifts may be needed where the sub-brackets cannot be reached from the floor.
Level the shade
Lay a bubble level along the fabric roll and turn the idler adjusting screw. Clockwise lowers the idler end, counter-clockwise raises it.
Check: Fabric roll level
Wire and power up
Wire the shade and set limits from P/N 045520. Run the shade up and down several times and fix any interference.
Check: Full travel without interference
Care and maintenance
No mechanical upkeep is needed. Adjustments and repairs go to the original provider and qualified personnel; dust the fabric in place.
Requirements Lutron states in 045625
What the guide requires for a Sivoia QS shade before and during installation:
- Ambient operating environment
- 32 °F to 104 °F (0 °C to 40 °C), 0 to 90% humidity non-condensing, indoor use only
- Tools required
- Power drill, level, tape measure, #2 Phillips screwdriver and a 1/4 in (6 mm) hex-head driver
- Bracket-to-bracket distance
- Tube width plus 1.5 in (38 mm), level and centered over the window, screws into a structural member that carries the operating load
- Screws per sub-bracket, by mount
- Ceiling or wall sub-bracket: 4
- Universal sub-bracket, ceiling or wall mount: 4
- Universal sub-bracket, jamb mount: 3
- Universal sub-bracket, combination mount: as the location allows, 4 minimum
- Supplied screws
- Self-drilling, for solid wood structural members
- Sub-bracket kits
- Ceiling, wall and universal kits each hold sub-brackets, mounting screws and a cable tie and anchor
- Cable entry
- Out of the wall, ceiling or jamb on the drive side, 12 to 18 in (30 to 45 cm) exposed. Clear of the sub-bracket and the moving fabric
- Cable at each sub-bracket
- Ceiling sub-bracket: beside or below, with a clearance hole for ceiling entry
- Wall sub-bracket: beside, above or below
- Universal sub-bracket: ceiling, wall or jamb, holes for ceiling and wall entry
- Crew
- 2 people, one at each end. 2 ladders or lifts where the sub-brackets are out of reach from the floor
- Hooking in
- ceiling mount: Top tab into the rear hook, front over the front hook
- Hooking in
- wall, universal: Tilted onto the upper tab, swung down onto the lower tab
- Securing
- Shade centered, then each bracket's securing screw fully tightened by hand screwdriver through the hook or tab. Each bracket then checked with a careful tug
- Leveling
- Bubble level along the fabric roll. Idler adjusting screw clockwise to lower, counter-clockwise to raise the idler end
Questions about document 045625
The answers come from Lutron document 045625 and New Way's record of it.
What is Lutron document 045625?
Lutron's six-page wall, ceiling and jamb mount guide for Roller 100, 150 and 300 shades, footer-stamped P/N 045625 Rev A. Pages 3 to 6 of Lutron document 045625 repeat the English pages in French and Spanish.
Which revision of 045625 is current?
Rev A, dated July 2018, is the revision Lutron publishes. New Way checked it against assets.lutron.com on 15 October 2026.
Which roller shades does 045625 cover?
Lutron Sivoia QS roller shades. For related steps Lutron refers readers to document 045520.
How far apart do the sub-brackets go?
Tube width plus 1.5 in (38 mm) bracket to bracket, per Lutron document 045625. Mark the positions level and centered over the window, with the screws in structure.
How many screws does each sub-bracket take?
Lutron document 045625 asks for 4 screws per ceiling or wall sub-bracket. The supplied self-drilling screws suit solid wood structural members.
- Universal on a ceiling or wall mount: 4
- Universal on a jamb mount: 3
- Universal on a combination mount: at least 4, as the location allows
Where should the shade cable come out?
On the drive side of the wall, ceiling or jamb, with 12 to 18 in (30 to 45 cm) exposed, per Lutron document 045625. Keep the cable clear of the sub-bracket and the moving fabric.
How is the shade leveled after hanging?
Lutron document 045625 checks the fabric roll with a bubble level. Turn the idler bracket screw clockwise to lower the idler end, counter-clockwise to raise it.
What clearance does the fabric need from trim?
Lutron document 045625 asks for ample clearance so the fabric cannot rub trim, window, top treatment or other objects. A wall mount may need spacer blocks, not included.
Other Sivoia QS installation guides
Installation guides for the same Sivoia QS system:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| 045211Roller Shades Installation Guide: Angled Coupler Chassis Addendum | Roller 100, Roller 300 | A | |
| 045707Roller Shades Installation Guide: Coupled Shades, Roller 100 / 150 / 300 | Roller 100, Roller 300 | B | |
| 045626Roller Shades Installation Guide: Roller 100/150/300, Fascia Mount Chassis | Roller 100, Roller 300 | A | |
| 045627ROLLER 100/150/300 – Pocket Mount Chassis Installation Guide | Roller 100, Roller 300 | A | Feb 2019 |
Documents used with 045625
Lutron document 045626 is the matching chassis mounting guide for the same shades with a fascia. Lutron documents 045707 and 045211 are the inline and angled coupled shade addenda, and 086106 the Roller 100 specification submittal.
| Document | Type | Revision | Date |
|---|---|---|---|
| 045520Basic Wiring and Setup Installation Guide | Installation Guide | B | Nov 2016 |
| 086106Roller Shades Specification Submittal: Roller 100 | Specification Submittal | B | May 2017 |
| 085511Roller Shades CAD Drawing: Roller 100/150/300 Ceiling Left Shade Bracket, Detail Drawing | CAD Drawing | A | |
| 085510Roller Shades CAD Drawing: Roller 100/150/300 Ceiling Right Shade Bracket, Detail Drawing | CAD Drawing | A | |
| Roller Shades Revit Family: Dual Roller 100/150/200 (Ceiling Mount) | Revit Family | ||
| Roller Shades Revit Family: Dual Roller 100/150/200 (Wall Mount) | Revit Family | ||
| Roller Shades Revit Family: Roller 100/150/200 (Pocket Mount) | Revit Family | ||
| Roller Shades Revit Family: Roller 100/150/200 (Wall Mount) | Revit Family | ||
| 0853144-Group RF Remote Control Specification Submittal | Specification Submittal | C | May 2016 |
| 369847Pico Wireless Control, 4-Button Specification Submittal | Specification Submittal | K | Mar 2024 |
Revisions of 045625
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| A | Jul 2018 | Current. The file on assets.lutron.com. Checked 15 Oct 2026. |
Not covered in 045625, and what to read next
Lutron document 045625 covers mounting without a fascia and prints no sub-bracket dimensions, load figure or wiring.
Publisher and citation for document 045625
Lutron Electronics Co., Inc. publishes document 045625, Rev A, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 15 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Sivoia QS?
New Way supplies and installs Lutron Sivoia QS shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 045625 filled in.
