You searched and this document matched it.
See all results045626 · Installation Guide · Rev A · English, French, Spanish, Portuguese · PDF, 8 pages, 8.3 MB
Lutron Sivoia QS Roller Shades Installation Guide: Roller 100/150/300, Fascia Mount Chassis (045626, rev A)
Lutron's chassis mounting guide for Roller 100, 150 and 300 shades with a fascia and an optional top back cover.
Lutron 045626 Rev A, Sivoia QS Roller Shades Installation Guide: Roller 100/150/300, Fascia Mount Chassis. https://assets.lutron.com/a/documents/045626.pdf, via https://newwaykl.com/resources/lutron/roller-shades/sivoia-qs/lutron-sivoia-qs-roller-shades-installation-guide-045626/
About document 045626
Lutron document 045626, Rev A of March 2019, is the fascia mount chassis installation guide: top back cover fixing, sub-bracket marking, cable entry, hanging, wiring and the fascia, in English, French, Spanish and Portuguese.
What guide 045626 covers
Lutron document 045626 has these ten sections. Each link opens the PDF at that page in a new tab.
- Prepare to install: notes, items and tools, opens in a new tab page 1
- Mount the optional top back cover, opens in a new tab page 1
- Mark the sub-bracket locations, opens in a new tab page 1
- Cable entry, opens in a new tab page 1
- Install the sub-brackets: wall, ceiling and jamb mount, opens in a new tab page 1
- Hang the shade in the sub-brackets, opens in a new tab page 1
- Level the shade, opens in a new tab page 1
- Wire the shade and power up, opens in a new tab page 2
- Mount the fascia, opens in a new tab page 2
- Care and maintenance, opens in a new tab page 2
Specifications in 045626
Lutron document 045626 prints 21 values in the groups the document uses, each with the document's unit. The page link beside each group opens the PDF where the group starts.
Important notes
PDF page 1 of 045626, opens in a new tab- Ambient operating temperature
- 32 °F to 104 °F (0 °C to 40 °C)
- Humidity
- 0 to 90%, non-condensing
- Location
- Indoor use only
- Wiring and programming reference
- Sivoia QS Basic Wiring and Setup, P/N 045520
Tools required
PDF page 1 of 045626, opens in a new tab- Hex-head driver
- 1/4 in (6 mm)
Mount the optional top back cover
PDF page 1 of 045626, opens in a new tab- Mounting position
- Inside or above the window opening
- Fastener pairs
- 1 pair per 36 in (914 mm) of width
- Spacing between fastener pairs
- 36 in (914 mm) maximum
- Screws from the cover ends
- 3 in (76 mm) minimum
Mark the sub-bracket locations
PDF page 1 of 045626, opens in a new tab- Bracket-to-bracket distance
- Tube width + 1.5 in (38 mm)
- Spacer blocks for wall mount
- May be required to clear the trim (not included)
Cable entry
PDF page 1 of 045626, opens in a new tab- Cable exit
- Wall, ceiling or jamb, drive side
- Cable left exposed
- 12 to 18 in (300 to 450 mm)
- Sub-bracket clearance holes
- Ceiling and jamb cable entries
Install the sub-brackets
PDF page 1 of 045626, opens in a new tab- Wall mount
- 4 screws through the rear of the sub-bracket
- Ceiling mount
- 4 screws through the top of the sub-bracket
- Jamb mount
- 4 screws through the top of the sub-bracket
- Supplied mounting screws
- Self-drilling, for solid wood
Hang the shade
PDF page 1 of 045626, opens in a new tab- People needed
- 2, one supporting each end
Level the shade
PDF page 1 of 045626, opens in a new tab- Idler adjusting screw
- Clockwise lowers, counter-clockwise raises the idler end
Mount the fascia
PDF page 2 of 045626, opens in a new tab- Bottom bar at the upper limit
- Below the dotted line in the profile view
Installation walk-through for 045626
Lutron document 045626 gives ten steps, in the document's order, after the tools and fixings it lists.
The clearance, the check and the warning under a step are the document's own.
Tools
- 1/4 in (6 mm) hex-head driver
- #2 Phillips screwdriver
- Level
- Tape measure
- Power drill
Fixings
- Self-drilling mounting screws (supplied, for solid wood)
- Cable tie and anchor (supplied)
- Top back cover fasteners in pairs, appropriate for the wall or ceiling
- Installer-chosen fasteners for other surfaces, able to carry the operating load
- Spacer blocks for a wall mount where needed (not included)
Prepare
Read the important notes and check the shades, sub-brackets, screws, fascia and any top back cover.
Check: Parts and tools present
Mount the optional top back cover
Fix the cover inside or above the opening with fastener pairs into the wall or ceiling. Pre-drill where possible, do not over-tighten, and shim the cover true.
Clearance: 1 pair per 36 in (914 mm) of width; screws at least 3 in (76 mm) from the cover ends
Check: Cover level, straight and untwisted
Warning: Screws too near the cover ends foul the shade brackets
Mark the sub-bracket locations
Mark the sub-brackets on the surface or top back cover, level and centered over the window. Put them over structure, with clearance for the fabric.
Clearance: Tube width + 1.5 in (38 mm)
Check: Marks level and centered
Plan the cable entry
Bring the cable out on the drive side through the sub-bracket's ceiling or jamb clearance holes. Or bring it out beside or below the sub-bracket, without clashing with it.
Clearance: 12 to 18 in (300 to 450 mm) exposed
Check: Cable cannot touch the moving fabric
Install the sub-brackets
Fix each sub-bracket at its marks with 4 screws. Drive them through the rear for a wall mount, or through the top for a ceiling or jamb mount.
Clearance: 4 screws per sub-bracket
Check: Fasteners suit the surface and load
Warning: Supplied screws suit solid wood only
Hang the shade
With one person at each end, insert the bracket tabs into the rear hangers. Lift the front so the front hooks ride over the front hangers.
Center the shade and tighten each securing screw with the Phillips screwdriver.
Check: Each end passes a careful tug
Level the shade
Check the fabric roll with a bubble level; turn the idler adjusting screw clockwise to lower or counter-clockwise to raise.
Check: Fabric roll level
Wire and power up
Wire the shade and set limits from P/N 045520. Run it up and down several times and fix any interference.
Check: Full travel without interference
Mount the fascia
Hook the fascia's top lip on the upper hooks and check full engagement. Swing the bottom under the shade and snap the triangular lip behind the lower tabs.
Center the fascia and run the shade to both limits several times.
Check: Fabric touches neither fascia nor anything else
Warning: The upper limit must keep the bottom bar out of the sub-brackets
Care and maintenance
No mechanical upkeep is needed. Adjustments and repairs go to the original provider and qualified personnel; dust the fabric in place.
Count the top back cover fastener pairs from 045626
Lutron document 045626 spaces the fastener pairs along the top back cover: one at each end, at least 3 in (76 mm) in from the end. The rest sit at most 36 in (914 mm) apart.
Enter the top back cover width to count the fastener pairs along the top back cover.
From Lutron document 045626, page 1; confirm against the PDF before you drill.
Requirements Lutron states in 045626
What the guide requires for a Sivoia QS shade before and during installation:
- Ambient operating environment
- 32 °F to 104 °F (0 °C to 40 °C), 0 to 90% humidity non-condensing, indoor use only
- Tools required
- Power drill, tape measure, level, #2 Phillips screwdriver and a 1/4 in (6 mm) hex-head driver
- Top back cover fixing
- One fastener pair per 36 in (914 mm) of width, at least 3 in (76 mm) from the cover ends, shimmed level and untwisted
- Bracket-to-bracket distance
- Tube width plus 1.5 in (38 mm), marked on the surface or the top back cover, level and centered, into structure
- Cable entry
- Drive side, 12 to 18 in (300 to 450 mm) exposed, through the sub-bracket's ceiling or jamb clearance holes or beside or below it
- Screws per sub-bracket
- 4, through the rear for a wall mount and through the top for ceiling and jamb mounts. Supplied self-drilling screws suit solid wood
- Hanging the shade
- Two people. Tabs into the rear hangers, front hooks over the front hangers, securing screws tightened and tug-checked
- Leveling
- Bubble level along the fabric roll. Idler adjusting screw clockwise to lower, counter-clockwise to raise
- Fitting the fascia
- Top lip on the upper hooks, bottom swung under the shade, triangular lip snapped behind the lower tabs
- Upper limit with a fascia
- Set so the bottom bar stays below the profile view's dotted line and is not drawn into the sub-brackets
Questions about document 045626
The answers come from Lutron document 045626 and New Way's record of it.
What is Lutron document 045626?
Lutron's eight-page fascia mount guide for Roller 100, 150 and 300 shades, footer-stamped P/N 045626 Rev A. Pages 3 to 8 of Lutron document 045626 repeat the English pages in French, Spanish and Portuguese.
Which revision of 045626 is current?
Rev A is the revision Lutron publishes. New Way checked it against assets.lutron.com on 15 October 2026.
Which roller shades does 045626 cover?
Lutron Sivoia QS roller shades. For related steps Lutron refers readers to document 045520.
How is the optional top back cover fixed?
One fastener pair per 36 in (914 mm) of cover width, per Lutron document 045626. Every screw sits at least 3 in (76 mm) from the cover ends.
How many screws does each sub-bracket take, and where?
Lutron document 045626 uses 4 screws per sub-bracket. Wall mounts take them through the rear, ceiling and jamb mounts through the top.
How does the fascia go on?
Lutron document 045626 hooks the fascia's top lip on the upper hooks. The triangular lip then snaps behind the lower tabs.
How far apart are the sub-brackets and how much cable is left?
Tube width plus 1.5 in (38 mm) between the sub-brackets, per Lutron document 045626. Lutron leaves 12 to 18 in (300 to 450 mm) of cable exposed on the drive side.
Can the shade be mounted inside or outside the opening?
Lutron document 045626 shows both outside and inside mounts, with the top back cover inside or above the opening.
Other Sivoia QS installation guides
Installation guides for the same Sivoia QS system:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| 045211Roller Shades Installation Guide: Angled Coupler Chassis Addendum | Roller 100, Roller 300 | A | |
| 045707Roller Shades Installation Guide: Coupled Shades, Roller 100 / 150 / 300 | Roller 100, Roller 300 | B | |
| 045625Roller Shades Installation Guide: Roller 100/150/300, Ceiling Mount Chassis | Roller 100, Roller 300 | A | Jul 2018 |
| 045627ROLLER 100/150/300 – Pocket Mount Chassis Installation Guide | Roller 100, Roller 300 | A | Feb 2019 |
Documents used with 045626
Lutron document 045625 is the matching guide for the same shades without a fascia. Lutron document 086106 is the Roller 100 specification submittal, and 045707 and 045211 are the coupled shade addenda.
| Document | Type | Revision | Date |
|---|---|---|---|
| 045520Basic Wiring and Setup Installation Guide | Installation Guide | B | Nov 2016 |
| 086106Roller Shades Specification Submittal: Roller 100 | Specification Submittal | B | May 2017 |
| 085398Roller Shades CAD Drawing: Roller 100/150/300 in 4″ (103mm) Square Fascia, Section View | CAD Drawing | A | |
| 085385Roller Shades CAD Drawing: Roller 100/150/300 Left Fascia Bracket, Detail Drawing | CAD Drawing | A | |
| Roller Shades Revit Family: Dual Roller 100/150/200 (Ceiling Mount) | Revit Family | ||
| Roller Shades Revit Family: Dual Roller 100/150/200 (Wall Mount) | Revit Family | ||
| Roller Shades Revit Family: Roller 100/150/200 (Pocket Mount) | Revit Family | ||
| Roller Shades Revit Family: Roller 100/150/200 (Wall Mount) | Revit Family | ||
| 0853144-Group RF Remote Control Specification Submittal | Specification Submittal | C | May 2016 |
| 369847Pico Wireless Control, 4-Button Specification Submittal | Specification Submittal | K | Mar 2024 |
Revisions of 045626
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| A | Not stated | Current. The file on assets.lutron.com. Checked 15 Oct 2026. |
Not covered in 045626, and what to read next
Lutron document 045626 prints no fascia or bracket dimensions and no wiring.
Publisher and citation for document 045626
Lutron Electronics Co., Inc. publishes document 045626, Rev A, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 15 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Sivoia QS?
New Way supplies and installs Lutron Sivoia QS shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 045626 filled in.
