You searched and this document matched it.
See all results086106 · Specification Submittal · Rev B · May 2017 · English · PDF, 10 pages, 2.4 MB
Lutron Sivoia QS Roller Shades Specification Submittal: Roller 100 (086106, rev B)
Lutron's specification submittal for the Sivoia QS Roller 100 chassis, carrying up to 100 sq ft (10 sq m) of fabric per drive.
Lutron 086106 Rev B (May 2017), Sivoia QS Roller Shades Specification Submittal: Roller 100. https://assets.lutron.com/a/documents/086106.pdf, via https://newwaykl.com/resources/lutron/roller-shades/sivoia-qs/lutron-sivoia-qs-roller-shades-specification-submittal-086106/
About document 086106
Lutron document 086106, Rev B of May 2017, is the Roller 100 chassis specification submittal: noise, accuracy, power, system capacity, grouping, integration, shade options, light gaps, brackets and coupled systems.
What submittal 086106 covers
Lutron document 086106 has these eight sections. Each link opens the PDF at that page in a new tab.
- Overview, features and specifications, opens in a new tab page 1
- Power and system capacity, opens in a new tab page 2
- Performance, grouping, integration and controls, opens in a new tab page 2
- Roller 100 shade options, opens in a new tab page 3
- Dimensions and light gaps, opens in a new tab page 4
- Bracket options, opens in a new tab page 5
- Coupled systems and bottom bar alignment, opens in a new tab page 9
- Sub-brackets for coupled systems, opens in a new tab page 10
Specifications in 086106
Lutron document 086106 prints 60 values in the groups the document uses, each with the document's unit. The page link beside each group opens the PDF where the group starts.
Features and specifications
PDF page 1 of 086106, opens in a new tab- Noise
- 38 dBA maximum at 3 ft (1 m) from the EDU
- Shade alignment
- Within 0.125 in (3 mm) at all times
- Light gap, fabric to outside edge of shade bracket
- 0.75 in (19 mm), symmetrical
- Power
- 24 to 36 V DC low voltage
- Power failure memory
- Lifetime of the product
- Limited warranty
- 8 years
- Operating voltage
- Low-voltage Class 2, 35 V DC power supply required
- Overvoltage protection (spike and brownout)
- +/- 10% of line voltage
- ESD protection
- Provided by the power supply
- Power source
- Lutron approved NEC Class 2
System capacity
PDF page 2 of 086106, opens in a new tab- Devices per system
- 100
- Zones per system
- 100
- Maximum shade fabric per EDU
- 100 sq ft (10 sq m)
Performance
PDF page 2 of 086106, opens in a new tab- Symmetrical light gaps
- As small as 0.75 in (19 mm) each side
- Positions stored in each EDU
- Presets at any stop point, plus full open and full close limits
- Stopping accuracy
- 0.125 in (3 mm) steps
- Preset adjustment
- 5 second press and hold
- Alignment, multiple EDUs
- Within 0.125 in (3 mm)
Integration
PDF page 2 of 086106, opens in a new tab- Lutron lighting control
- GRAFIK Eye QS, no separate interface
- Other equipment
- Contact closure, R232 (as printed), Ethernet
- Control points
- GRAFIK Eye QS shade columns or seeTouch QS keypads
- Communications link
- Shades, GRAFIK Eye QS and seeTouch QS keypads on the same link
- seeTouch QS keypads
- Low voltage
Shade options
PDF page 3 of 086106, opens in a new tab- Mounting
- Pocket, inside or outside the window frame
- Drive side
- Left or right
- Fabric drop
- Regular roll or reverse roll
- Bottom bars
- Designer (standard), Exposed, Sealed, Architectural Half-Wrap, Architectural Exposed
- Bottom bar colors (Exposed, Architectural Half-Wrap, Architectural Exposed)
- White, black, bronze, silver or custom
- Fabric types
- Sheer, privacy, room darkening
Dimensions
PDF page 4 of 086106, opens in a new tab- Light gap each side
- 0.75 in (19 mm)
- Dimension marked on the wall sub-bracket drawing
- 3.45 in (88 mm)
- Dimension marked on the wall sub-bracket drawing
- 3.26 in (83 mm)
Bracket options: ceiling mount
PDF page 5 of 086106, opens in a new tab- Dimension marked on the drawing
- 3.30 in (84 mm)
- Dimension marked on the drawing
- 4.39 in (111 mm)
- Dimension marked on the drawing
- 5.20 in (132 mm)
Bracket options: wall mount
PDF page 5 of 086106, opens in a new tab- Dimension marked on the drawing
- 5.0 in (127 mm)
- Dimension marked on the drawing
- 4.3 in (109 mm)
Bracket options: jamb mount
PDF page 6 of 086106, opens in a new tab- Dimension marked on the drawing
- 4.3 in (109 mm)
- Dimension marked on the drawing
- 5.1 in (129.5 mm)
- Dimension marked on the drawing
- 4.48 in (114 mm)
Bracket options: fascia mount
PDF page 6 of 086106, opens in a new tab- Dimension marked on the drawing
- 4.20 in (107 mm)
- Dimension marked on the drawing
- 4.20 in (107 mm)
Bracket options: pocket mount
PDF page 7 of 086106, opens in a new tab- Dimension marked on the drawing
- 4.75 in (121 mm)
- Dimension marked on the drawing
- 5.0 in (127 mm)
Bracket options: dual mount
PDF page 8 of 086106, opens in a new tab- Dimension marked on the drawing
- 6.5 in (165 mm)
- Dimension marked on the drawing
- 9.0 in (229 mm)
- Minimum pocket size
- 7 in deep x 11 in high (178 mm x 279 mm)
Coupled systems
PDF page 9 of 086106, opens in a new tab- Panels per EDU
- Up to 6
- Minimum light gap between panels
- 1.5 in (38 mm)
- Bottom bar alignment
- Within 0.125 in (3 mm)
- Mounting options
- Available with all mounting options
Sub-brackets for coupled systems
PDF page 10 of 086106, opens in a new tab- Dimension marked on the fascia-mount plan view
- 4.05 in (103 mm)
- Dimension marked on the fascia-mount elevation view
- 6.14 in (156 mm)
- Dimension marked on the fascia-mount elevation view
- 4.08 in (104 mm)
- Dimension marked on the pocket-mount plan view
- 3.13 in (79.5 mm)
- Dimension marked on the pocket-mount elevation view
- 8.48 in (215 mm)
- Dimension marked on the pocket-mount elevation view
- 4.17 in (106 mm)
- Dimension marked on the dual-mount plan view
- 3.75 in (95 mm)
- Dimension marked on the dual-mount plan view
- 3.0 in (76 mm)
- Dimension marked on the dual-mount elevation view
- 8.36 in (212 mm)
Facts Lutron states in 086106
The values Lutron document 086106 states, as published:
- Noise
- No louder than 38 dBA at 3 ft (1 m) from the EDU
- Alignment and stopping accuracy
- Grouped shades stay within 0.125 in (3 mm) of each other. Each EDU stops in 0.125 in (3 mm) steps over the full travel
- Presets
- Anywhere between the open and close limits. Adjusted with a 5 second press and hold on a seeTouch QS keypad or GRAFIK Eye QS
- Limits
- Set from the EDU, keypads or GRAFIK Eye QS
- Light gap
- 0.75 in (19 mm) between the fabric and the outside edge of each shade bracket, the same on both sides
- Power
- 24 to 36 V DC low voltage
- Class 2, with a 35 V DC supply required
- From a Lutron approved NEC Class 2 source
- Power failure memory for the product's lifetime
- System capacity
- 100 devices and 100 zones per system. 100 sq ft (10 sq m) of fabric per EDU
- Grouping
- Keypads control any EDU, group or subgroup with no separate group controller. Groups change at the point of control without rewiring
- Integration
- GRAFIK Eye QS without a separate interface. Contact closure, 'R232' (as printed) and Ethernet for other equipment
- Options
- Pocket, inside or outside mount
- Left or right drive
- Regular or reverse roll
- Five bottom bars
- Sheer, privacy and room darkening fabrics
- Full blackout
- Side channels plus a pocket, or a fascia and top back cover
- Bracket design
- Two-piece: a sub-bracket plus a shade bracket factory installed on the shade. For ceiling, wall, jamb, fascia, pocket and dual mounts
- Dual mount pocket
- 7 in deep x 11 in high (178 mm x 279 mm) minimum, for a sheer and a blackout on one window
- Coupled systems
- Up to six panels on one EDU, 1.5 in (38 mm) minimum gap between panels, bottom bars within 0.125 in (3 mm)
- Warranty
- The page 1 features list states an 8 year limited warranty
Questions about document 086106
The answers come from Lutron document 086106 and New Way's record of it.
What is Lutron document 086106?
Lutron's ten-page Roller 100 chassis specification submittal, footer-dated 11 May 2017 as 086106b. Lutron prints job name, job number and model number fields for a tender.
Lutron's EDU sits inside the roller shade assembly, tracks the shade's position and moves it to presets.
Which revision of 086106 is current?
Rev B, dated May 2017, is the revision Lutron publishes. New Way checked it against assets.lutron.com on 15 October 2026.
Which roller shades does 086106 cover?
Lutron Sivoia QS roller shades.
How quiet is the Roller 100?
Lutron document 086106 caps Roller 100 noise at 38 dBA, measured 3 ft (1 m) from the EDU.
How much fabric and how many panels per Roller 100 drive?
Lutron document 086106 allows 100 sq ft (10 sq m) of fabric per EDU and up to six coupled panels on one EDU. Fabric and panel size limits come from the shade ordering tool or from Lutron.
What light gap should the architect expect?
Lutron document 086106 gives 0.75 in (19 mm) on each side, between the fabric and the outside edge of the shade brackets. Coupled panels keep a 1.5 in (38 mm) minimum gap between them.
What power and system limits apply?
Lutron document 086106 calls for low-voltage Class 2 power with a 35 V DC supply. The supply comes from a Lutron approved NEC Class 2 source, and the system allows 100 devices and 100 zones.
What pocket does a dual mount need?
Lutron document 086106 sets the dual mount pocket at 7 in deep by 11 in high (178 mm by 279 mm) minimum. The dual mount carries two fabrics on one window, typically a sheer and a blackout.
Other Sivoia QS specification submittals
Specification submittals for the same Sivoia QS system:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| 0853144-Group RF Remote Control Specification Submittal | C | May 2016 | |
| 085274Hard Wired Power Supply Specification Submittal | D | Aug 2014 | |
| 369847Pico Wireless Control, 4-Button Specification Submittal | K | Mar 2024 | |
| 369374Roller Shades Specification Submittal: QS Contact Closure Input/Output Interface | H | Apr 2026 |
Documents used with 086106
Lutron document 045190 is the Roller 100 dual mount chassis guide; 045707 and 045211 are the coupled shade addenda. Lutron document 045604 is the QS power supply junction box installation guide.
| Document | Type | Revision | Date |
|---|---|---|---|
| 045190Roller 100 Installation Guide: Dual Mount Chassis | Installation Guide | B | Dec 2012 |
| 045707Roller Shades Installation Guide: Coupled Shades, Roller 100 / 150 / 300 | Installation Guide | B | |
| 045211Roller Shades Installation Guide: Angled Coupler Chassis Addendum | Installation Guide | A | |
| 045604Roller Shades Installation Guide: QS Power Supply J-Box Mount | Installation Guide | A | |
| 045627ROLLER 100/150/300 – Pocket Mount Chassis Installation Guide | Installation Guide | A | Feb 2019 |
| 045625Roller Shades Installation Guide: Roller 100/150/300, Ceiling Mount Chassis | Installation Guide | A | Jul 2018 |
| 085402Roller Shades CAD Drawing: Roller 100 in Armstrong Compatible 5″ Pocket Elevation View | CAD Drawing | A | |
| 085401Roller Shades CAD Drawing: Roller 100 in Armstrong Compatible 5″ Pocket Section View | CAD Drawing | A | |
| Roller Shades Revit Family: Dual Roller 100/150/200 (Ceiling Mount) | Revit Family | ||
| Roller Shades Revit Family: Dual Roller 100/150/200 (Wall Mount) | Revit Family |
Revisions of 086106
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| B | May 2017 | Current. The file on assets.lutron.com. Checked 15 Oct 2026. |
Not covered in 086106, and what to read next
Lutron document 086106 is a datasheet with no installation steps or wiring.
Publisher and citation for document 086106
Lutron Electronics Co., Inc. publishes document 086106, Rev B, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 15 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Sivoia QS?
New Way supplies and installs Lutron Sivoia QS shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 086106 filled in.
