You searched and this document matched it.
See all results045506 · Installation Guide · Rev B · Aug 2017 · English, French, Spanish · PDF, 2 pages, 4.4 MB
Lutron Serena Roller Shades Installation Guide (045506, rev B)
Lutron's setup and operation guide for the Serena battery-powered roller shade: pairing, limits, favorite level and factory reset.
Lutron 045506 Rev B (August 2017), Serena Roller Shades Installation Guide. https://assets.lutron.com/a/documents/045506.pdf, via https://newwaykl.com/resources/lutron/roller-shades/serena/lutron-serena-roller-shades-installation-guide-045506/
About document 045506
Lutron document 045506, Rev B of August 2017, is the Serena roller shade setup and operation guide: the shade button, assigning a Pico or 4-Group RF remote, limits, favorite level, factory defaults and drive models.
What guide 045506 covers
Lutron document 045506 has these eight sections. Each link opens the PDF at that page in a new tab.
- The shade button and Smart Bridge note, opens in a new tab page 1
- Assigning a control: compatible controls, opens in a new tab page 1
- Assign a Pico wireless control, opens in a new tab page 1
- Assign a Lutron 4-Group RF remote control, opens in a new tab page 1
- Adjusting shade limits (optional), opens in a new tab page 1
- Setting a favorite level (optional), opens in a new tab page 2
- Restoring factory default settings, opens in a new tab page 2
- Shade drive models and regulatory information, opens in a new tab page 2
Specifications in 045506
Lutron document 045506 prints 17 values in the groups the document uses, each with the document's unit. A row names the catalog codes it applies to. The page link beside each group opens the PDF where the group starts.
- Shade button
- Single button with LED
- With a Lutron Smart Bridge installed
- Program and control from the Lutron App
Assigning a control
PDF page 1 of 045506, opens in a new tab- Compatible controls
- Pico wireless control; Lutron 4-Group RF remote control (sold separately)
Adjusting shade limits
PDF page 1 of 045506, opens in a new tab- Factory limits
- Pre-programmed from the window dimensions and mounting option
Setting a favorite level
PDF page 2 of 045506, opens in a new tab- Factory favorite level
- Midpoint between the shade limits
Restoring factory defaults
PDF page 2 of 045506, opens in a new tab- Shade reset removes
- All control assignments and favorite programming; limits retained
- Pico reset, hold time to solid LED
- About 3 seconds
- 4-Group remote reset, LED on time
- About 3 to 5 seconds
- Remote reset removes
- All shade assignments and favorite programming
Shade drive models
PDF page 2 of 045506, opens in a new tab- Rating and frequency
- 6 to 12 V DC, 5 W, 431 to 437 MHzModels: SYC-J-EDU-R2
- Rating and frequency
- 6 to 12 V DC, 5 W, 433.05 to 434.79 MHzModels: SYC-Q-EDU-R2
- Rating and frequency
- 6 to 12 V DC, 5 W, 868.125 to 868.475 MHzModels: SYC-M-EDU-R2
- Rating and frequency
- 6 to 12 V DC, 5 W, 868.125 to 869.85 MHzModels: SYC-K-EDU-R2
FCC information
PDF page 2 of 045506, opens in a new tab- FCC
- Class B digital device, Part 15Models: SYC-J-EDU-R2
- Canada
- ICES-003, Class B
IC information
PDF page 2 of 045506, opens in a new tab- Industry Canada
- License-exempt RSS standard(s)
CE information
PDF page 2 of 045506, opens in a new tab- EU radio equipment directive
- 2014/53/EUModels: SYC-K-EDU-R2
Installation walk-through for 045506
Lutron document 045506 gives eight steps, in the document's order.
The clearance, the check and the warning under a step are the document's own.
Check for a Smart Bridge
Find the shade button with its LED on the shade. Lutron uses it to start and confirm each programming step.
If a Lutron Smart Bridge is installed in the home, program and control the shade from the Lutron App. The button steps below do not apply.
Check: Shade button located
Assign a Pico wireless control
Tap the shade button once and wait for it to light. Press and hold the Close button on the Pico.
When the shade button flashes, the Pico is assigned. Repeat the steps for each further assignment.
Check: Shade button flashed
Assign a Lutron 4-Group RF remote
Tap the shade button and wait for it to light. Pick the shade group button on the remote that should drive this shade and hold it down.
A flash of the shade button confirms the assignment. Repeat for any further assignments.
Check: Shade button flashed
Adjust the limits, if needed
Skip to step 5 if the factory limits suit the window.
Tap the shade button and wait for its light. Hold Open and Raise together until the shade button flashes and stays on.
Drive the shade with Raise and Lower to the top or bottom position you want. Hold Open to store the upper limit or Close to store the lower one.
Check: Shade button flashes to confirm the limit
Set a favorite level, if wanted
Drive the shade with Raise and Lower to the level you want. Hold the Favorite button until the shade button flashes.
Several shades on one control can hold different favorites. First take one battery out of each shade that should not change.
Check: Shade button flashes to confirm the favorite
Reset the shade to factory defaults
Tap the shade button quickly three times, holding after the third tap until the LED blinks green fast. Straight away tap it three more times.
The LED blinks green fast, then red and green three times, and goes out. Control assignments and the favorite are cleared and the limits stay.
Check: LED off after the red and green blinks
Reset a Pico
Triple tap the top or bottom button and keep holding after the third tap. The LED beside the top button glows steadily after about 3 seconds.
Release, then triple tap again at once. The LED flashes quickly, and the reset is complete when it stops.
Check: LED has stopped flashing
Warning: A reset removes all shade assignments and favorite programming
Reset a 4-Group remote
Tap All Shade Groups, then triple tap Open or Close and keep holding after the third tap. The All Shade Groups LED lights for about 3 to 5 seconds.
Hold on until that LED goes out, then release and triple tap at once. The group 1 to 4 LEDs and All Shade Groups light for about 3 to 5 seconds, then go out.
Check: All LEDs off: the remote is reset
Requirements Lutron states in 045506
What the guide requires for a Serena shade before and during installation:
- Scope
- Setup and operation of a battery-powered Serena roller shade from its single shade button with LED. With a Lutron Smart Bridge installed, the Lutron App programs and controls the shade instead.
- Compatible controls
- Pico wireless control and Lutron 4-Group RF remote control, sold separately
- Assign a Pico
- Tap the shade button and wait for it to light
- Press and hold the Pico Close button until the shade button flashes
- Repeat for each further assignment
- Assign a 4-Group remote
- Tap the shade button and wait for it to light. Hold the chosen shade group button until the shade button flashes.
- Limits
- Pre-programmed from the window dimensions and mounting option. To adjust:
- Tap the shade button
- Hold Open and Raise until the button flashes, then stays lit
- Position the shade
- Hold Open (upper limit) or Close (lower limit) until it flashes
- Favorite level
- Factory set to the midpoint between the limits. Position the shade, then hold Favorite until the shade button flashes. Any other shade on the same control keeps its own favorite if one battery is removed first.
- Factory reset of the shade
- Triple tap and hold the button until the LED blinks green rapidly
- Triple tap again; LED blinks red then green three times, then off
- Control assignments and the favorite are removed, the limits kept
- Factory reset of a Pico
- Triple tap and hold the top or bottom button
- Hold until the top-button LED stays on, about 3 seconds
- Release and triple tap again
- The reset is done when the fast flashing stops
- 4-Group remote factory reset
- Tap All Shade Groups, then triple tap and hold Open or Close
- All Shade Groups LED goes out after about 3 to 5 seconds
- Release and triple tap again
- The reset is done when every LED turns off
- What a remote reset removes
- Restoring factory defaults on a Pico or 4-Group remote removes all shade assignments and favorite programming
- Drive models
- All four drives: 6 to 12 V DC, 5 W
- SYC-J-EDU-R2: 431 to 437 MHz
- SYC-Q-EDU-R2: 433.05 to 434.79 MHz
- SYC-M-EDU-R2: 868.125 to 868.475 MHz
- SYC-K-EDU-R2: 868.125 to 869.85 MHz
- Regulatory
- FCC Part 15 Class B for SYC-J-EDU-R2, Canadian ICES-003 and Industry Canada license-exempt RSS, and EU Directive 2014/53/EU for SYC-K-EDU-R2
Questions about document 045506
The answers come from Lutron document 045506 and New Way's record of it.
What is Lutron document 045506?
Lutron's two-page Serena setup and operation guide, P/N 045506 revision B, dated 08/2017. English, French and Spanish print side by side on both pages.
Which revision of 045506 is current?
Rev B, dated August 2017, is the revision Lutron publishes. New Way checked it against assets.lutron.com on 15 October 2026.
Which roller shades does 045506 cover?
Lutron Serena roller shades.
How do I pair a Pico with a Lutron Serena roller shade?
Lutron document 045506 assigns a Pico from the shade button: tap it, wait for the light, then hold Pico Close. The shade button flashes when the assignment is made.
The same sequence is repeated for each further shade or control.
Do I need to set the limits on a new shade?
Lutron document 045506 makes limit setting optional: the limits come pre-programmed from the window dimensions and mounting option.
To adjust one, tap the shade button, hold Open and Raise on the remote, and position the shade. Then hold Open for the upper limit or Close for the lower one.
What does a factory reset of the shade remove?
Lutron document 045506 says a shade reset removes all control assignments and the favorite but keeps both limits.
The installer triple taps and holds the shade button until the LED blinks green rapidly. A second triple tap makes the LED blink red then green three times and turn off.
What if the home has a Lutron Smart Bridge?
Lutron document 045506 hands programming and control to the Lutron App when a Lutron Smart Bridge is installed. The shade button steps on the sheet then do not apply.
Which drive models does the guide list?
Lutron document 045506 lists four Serena drives, each rated 6 to 12 V DC and 5 W.
- SYC-J-EDU-R2: 431 to 437 MHz
- SYC-Q-EDU-R2: 433.05 to 434.79 MHz
- SYC-M-EDU-R2 and SYC-K-EDU-R2: 868.125 to 868.475 MHz and 868.125 to 869.85 MHz
Other Serena installation guides
Installation guides for the same Serena system:
All 9 Serena installation guidesDocuments used with 045506
Lutron document 045956 is the Serena battery-powered roller shade installation guide, and 085312 the Serena roller shades specification submittal. Lutron documents 0450010 and 045868 are the battery and wired-power EDU replacement guides; 045507 is the Triathlon setup guide.
| Document | Type | Revision | Date |
|---|---|---|---|
| 085312Roller Shades Specification Submittal | Specification Submittal | K | Sep 2025 |
| 085314Sivoia QS 4-Group RF Remote Control Specification Submittal | Specification Submittal | C | May 2016 |
| 369847Sivoia QS Pico Wireless Control, 4-Button Specification Submittal | Specification Submittal | K | Mar 2024 |
| 085575Roller Shades CAD Drawing: Battery, Architectural Fascia, Section View | CAD Drawing | D | |
| 085568Roller Shades CAD Drawing: Battery, Fabric Wrapped Fascia, Elevation View | CAD Drawing | B | |
| 08527610 Output Power Panel Power Supply (12 V) Specification Submittal | Specification Submittal | C | May 2016 |
| 085283Individual Plug-In Power Supply Specification Submittal | Specification Submittal | D | Nov 2018 |
| Application Note: Blink Codes | Application Note | ||
| 048561Application Note: Optimizing Battery Life in Shades | Application Note | F | Oct 2024 |
| 3687002Sivoia QS Roller Shades Product Brochure: Open Roll Shade (Sell Sheet) | Product Brochure | A |
Revisions of 045506
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| B | Aug 2017 | Current. The file on assets.lutron.com. Checked 15 Oct 2026. |
Not covered in 045506, and what to read next
Lutron document 045506 gives no mounting, wiring, battery installation or drive replacement steps.
Publisher and citation for document 045506
Lutron Electronics Co., Inc. publishes document 045506, Rev B, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 15 October 2026.
Lutron and Serena are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Serena?
New Way supplies and installs Lutron Serena shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 045506 filled in.
