You searched and this document matched it.
See all results085578 · CAD Drawing · Rev A · English · PDF, DWG, DXF
Lutron Sivoia QS Roller 100 CAD Drawing: Butt and Pass Corner Solution (085578)
Lutron's two-page CAD drawing of the butt and pass corner installation for Sivoia QS Roller 100/150/300 shades.
Lutron 085578 Rev A, Sivoia QS Roller 100 CAD Drawing: Butt and Pass Corner Solution. https://assets.lutron.com/a/documents/100_corner_option_1.pdf, via https://newwaykl.com/resources/lutron/roller-shades/sivoia-qs/lutron-sivoia-qs-roller-100-cad-drawing-butt-and-pass-corner-solution/
About document 085578
Lutron drawing 085578, revision A, is the butt and pass installation drawing: typical details with the light gaps on page 1, bracket details with the measurement deductions, clearances and roll-up per mounting on page 2.
What drawing 085578 covers
Lutron document 085578 has these eight sections. Each link opens the PDF at that page in a new tab.
- Butt and pass typical details, auxiliary views, opens in a new tab page 1
- Light gaps at maximum roll, both roll directions
- Wall bracket shown, pointer to the section drawing
- Installer clearance note, opens in a new tab page 1
- Butt and pass bracket details, top views, opens in a new tab page 2
- Measurement deductions and minimum clearance by mounting configuration, opens in a new tab page 2
- Maximum roll-up, roll tube centerline and projection adjust
- Title blocks with scale, page number and revision
Specifications in 085578
Lutron document 085578 prints 24 values in the groups the document uses, each with the document's unit. The page link beside each group opens the PDF where the group starts.
Auxiliary views
PDF page 1 of 085578, opens in a new tab- Regular roll light gap at max roll
- 5 in typical, inches only
- Reverse roll light gap at max roll
- 1 in typical, inches only
- Bracket shown
- Wall bracket
- Second scale printed on page 1
- 1/5
- Measurement deduction
- 4.8125 in (122 mm)
- Min clearance required
- 0.25 in (6 mm)
- Max rollup
- 4.00 in (102 mm) diameter
- Roll tube centerline
- 2.56 in (65 mm)
- Projection adjust
- -0.25 in/+0.25 in, inches only
- Measurement deduction
- 5.25 in (133 mm)
- Min clearance required
- 0.25 in (6 mm)
- Max rollup
- 4.00 in (102 mm) diameter
- Roll tube centerline
- 2.56 in (65 mm)
- Projection adjust
- -0.5 in/+0 in, inches only
- Measurement deduction
- 4.75 in (121 mm)
- Dashed line
- Butt and pass at a fascia
- Not recommended
- System height and detailed mounting requirements
- See the section drawing
- Deductions
- Minimum recommended, based on a 90 degree corner
- Adjustments at maximum roll diameter
- Not all available
title block
PDF page 1 of 085578, opens in a new tab- Drawing number
- 085578, on both pages
- Scale
- 1/4, on both pages
- Revision
- A, on both pages
- Pages
- 2
Facts Lutron states in 085578
The values Lutron document 085578 states, as published:
- Regular roll light gap
- 5 in typical at maximum roll, no metric value printed
- Reverse roll light gap
- 1 in typical at maximum roll, no metric value printed
- Bracket shown
- Wall bracket, on the page 1 typical details
- System height and mounting
- Not printed, Lutron refers the reader to the section drawing for system height and detailed mounting requirements
- Ceiling mount deduction
- 4.8125 in (122 mm) minimum recommended measurement deduction, with a 0.25 in (6 mm) minimum clearance required
- Wall mount deduction
- 5.25 in (133 mm) minimum recommended measurement deduction, with a 0.25 in (6 mm) minimum clearance required
- Pocket deduction
- 4.75 in (121 mm) minimum recommended measurement deduction, with a dashed line labeled pocket in the panel
- Fascia mount
- Marked not recommended for a butt and pass corner, with no dimensions printed in the fascia panel
- Basis of the deductions
- Lutron bases the minimum recommended deductions on a 90 degree corner
- Maximum roll-up
- 4.00 in (102 mm) diameter, printed in the ceiling and wall panels
- Roll tube centerline
- 2.56 in (65 mm) in the ceiling and wall panels
- Projection adjust
- -0.25 in/+0.25 in at the ceiling and -0.5 in/+0 in at the wall, in inches only
- Clearance note, both pages
- A factory-set shade has every clearance it needs to run
- Once adjustment features are used, the installer keeps proper clearances
- Some adjustments are not available at the maximum roll diameter
- Scale
- 1/4 on both pages, with a 1/5 scale also printed on page 1
- Pages and revision
- 2 pages, revision A, no date printed
- File formats
- PDF, DWG and DXF
- Not on the drawing
- Bracket dimensions, fastener sizes and fixings are not printed
Questions about document 085578
The answers come from Lutron document 085578 and New Way's record of it.
What is Lutron document 085578?
Lutron's drawing of the corner arrangement in which two shades butt and pass each other. Lutron publishes it as PDF, DWG and DXF, at 1/4 scale, with no date printed.
Which revision of 085578 is current?
Rev A is the revision Lutron publishes. New Way checked it against assets.lutron.com on 16 October 2026.
Which roller shades does 085578 cover?
Lutron Sivoia QS roller shades in the Roller 100 drive class.
Which roll direction leaves the smaller light gap at the corner?
Lutron drawing 085578 prints a typical light gap at maximum roll of 1 in for a reverse roll. A regular roll leaves 5 in; Lutron prints both light gaps in inches only.
Which mountings can a butt and pass corner use?
Lutron's page 2 of drawing 085578 gives bracket details for ceiling, wall and pocket mounting. The fascia panel is marked not recommended; page 1 shows the wall bracket.
How much do I deduct from the measurement at the corner?
Lutron drawing 085578 prints minimum recommended measurement deductions for a 90 degree corner, by mounting. Lutron's ceiling and wall panels also require a 0.25 in (6 mm) minimum clearance.
- Ceiling mount: 4.8125 in (122 mm)
- Wall mount: 5.25 in (133 mm)
- Pocket: 4.75 in (121 mm)
How much can the projection be adjusted at the corner?
Lutron drawing 085578 prints the projection adjust in inches only, in the ceiling and wall panels. Lutron's clearance note makes the installer responsible for proper clearances once an adjustment feature is used.
- Ceiling panel: -0.25 in/+0.25 in
- Wall panel: -0.5 in/+0 in
- Roll tube centerline in both panels: 2.56 in (65 mm)
Where is the system height for the corner?
Lutron does not print the system height on drawing 085578. Lutron's page 1 refers the reader to the section drawing for system height and detailed mounting requirements.
Other Sivoia QS Roller 100 CAD drawings
CAD drawings for the same Sivoia QS Roller 100 drive class:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| 085517Roller 100 CAD Drawing: Dual Narrow Sub-Bracket, Detail Drawing | Roller 100 | A | |
| 085384Roller 100 CAD Drawing: Wall Mount Shade, Elevation View | Roller 100 | C | |
| 085511Roller Shades CAD Drawing: Roller 100/150/300 Ceiling Left Shade Bracket, Detail Drawing | Roller 100, Roller 300 | A | |
| 085510Roller Shades CAD Drawing: Roller 100/150/300 Ceiling Right Shade Bracket, Detail Drawing | Roller 100, Roller 300 | A |
Documents used with 085578
Lutron drawings 085384 and 085517 are the wall mount shade elevation and the dual narrow bracket detail. Lutron drawings 085511 and 085510 are the ceiling left and right bracket details; three other Roller 100 corner drawings exist.
| Document | Type | Revision | Date |
|---|---|---|---|
| Roller 100 Installation Guide: Angled Coupler WIDR Tube, Light Gap Reference | Installation Guide | A | |
| Roller 100 Installation Guide: Angled Coupler, Light Gap Reference 2.5″ Tube | Installation Guide | A | |
| 0853144-Group RF Remote Control Specification Submittal | Specification Submittal | C | May 2016 |
| 369847Pico Wireless Control, 4-Button Specification Submittal | Specification Submittal | K | Mar 2024 |
| Roller Shades Revit Family: QS Shading Keypad 3-Group 3-Button with Raise/Lower | Revit Family | ||
| 085274Hard Wired Power Supply Specification Submittal | Specification Submittal | D | Aug 2014 |
| 048846Application Note: EU EcoDesign Standby Power Information | Application Note | A | Nov 2024 |
| 048863Roller Shades Application Note: Fabric Aesthetic Characteristics | Application Note | A | May 2026 |
| Revit Family: QS J-Box 35V Power Supply | Revit Family | ||
| Revit Family: QS Smart Power Panel, 30 Output | Revit Family |
Revisions of 085578
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| A | Not stated | Current. The file on assets.lutron.com. Checked 16 Oct 2026. |
Not covered in 085578, and what to read next
Lutron drawing 085578 prints no system height, bracket dimensions or fixings; the section drawing holds system height and mounting.
Publisher and citation for document 085578
Lutron Electronics Co., Inc. publishes document 085578, Rev A, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 16 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Sivoia QS?
New Way supplies and installs Lutron Sivoia QS shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 085578 filled in.
