You searched and this document matched it.
See all results085425 · CAD Drawing · Rev A · English · PDF, DWG, DXF
Lutron Sivoia QS Roller 64 CAD Drawing: Dual Mount Shade, Elevation View (085425)
Lutron's elevation view of a Roller 64 dual mount shade, view 2 at 1/4 scale.
Lutron 085425 Rev A, Sivoia QS Roller 64 CAD Drawing: Dual Mount Shade, Elevation View. https://assets.lutron.com/a/documents/0036-r064-dmt-f.pdf, via https://newwaykl.com/resources/lutron/roller-shades/sivoia-qs/lutron-sivoia-qs-roller-64-cad-drawing-dual-mount-shade-elevation-view/
About document 085425
Lutron drawing 085425, revision A, is the one-page Roller 64 dual mount elevation: minimum shade width, height and light gap, one unlabeled value, a top-view legend and notes on mounting and factory clearances.
What drawing 085425 covers
Lutron document 085425 has these six sections, all on its one page.
- Elevation view of the dual mount shade
- Legend keyed to the top view
- Minimum width, height and light gap
- Note on factory clearances and installer adjustments
- Note on ceiling, wall and jamb mounting
- Title block: scale, view, number and revision
Specifications in 085425
Lutron document 085425 prints twelve values in the groups the document uses, each with the document's unit. The page link beside each group opens the PDF where the group starts.
Elevation view, view 2
PDF page 1 of 085425, opens in a new tab- Minimum width of shade
- 17.5 in (445 mm)
- Minimum shade height
- 12 in (305 mm)
- Minimum light gap
- 0.75 in (19 mm)
- Unlabeled dimension
- 6.25 in (159 mm)
- Mounting configurations
- Ceiling, wall and jamb; wall mount shown
- Clearances
- All clearances in place as supplied by the factory; the installer keeps them when using adjustment features
- Adjustments at maximum roll diameter
- Not all available
Title block
PDF page 1 of 085425, opens in a new tab- Title
- Roller 64 dual mount
- Drawing
- 085425
- Scale
- 1/4
- View
- 2
- Revision
- A
Facts Lutron states in 085425
The values Lutron document 085425 states, as published:
- Subject
- Roller 64 dual mount shade, elevation (view 2)
- Minimum width of shade
- 17.5 in (445 mm)
- Minimum shade height
- 12 in (305 mm)
- Minimum light gap
- 0.75 in (19 mm)
- Unlabeled value
- 6.25 in (159 mm) is printed on the view without a label
- Mounting
- The bracket supports ceiling, wall and jamb mounting, with a wall mount drawn
- Clearances
- A shade fitted as supplied by the factory has the clearances it needs to operate
- After adjustment
- The installer keeps the clearances when adjustment features are used
- Adjustments
- Lutron notes that not every adjustment is available at the maximum roll diameter
- Legend
- Top-view legend keying views 1 and 2
- Scale, view and revision
- 1/4 scale, view 2, revision A, no date printed
- File formats
- PDF, DWG and DXF
Questions about document 085425
The answers come from Lutron document 085425 and New Way's record of it.
What is Lutron drawing 085425?
Lutron's one-page dual mount elevation, view 2 at 1/4 scale, published as PDF, DWG and DXF with no date printed. The top-view legend keys views 1 and 2, and 085424 is the matching section view.
Which revision of 085425 is current?
Rev A is the revision Lutron publishes. New Way checked it against assets.lutron.com on 16 October 2026.
Which roller shades does 085425 cover?
Lutron Sivoia QS roller shades in the Roller 64 drive class.
What is the smallest Roller 64 dual mount shade Lutron draws?
Lutron drawing 085425 prints a minimum width of shade of 17.5 in (445 mm) and a minimum shade height of 12 in (305 mm).
How much light gap does Lutron show on the dual mount elevation?
Lutron prints a minimum light gap of 0.75 in (19 mm) on drawing 085425. The drawing labels the figure as a minimum and gives no further rule for it.
Can the dual mount bracket go on a ceiling or a jamb?
Yes, Lutron notes on drawing 085425 that the bracket supports ceiling, wall and jamb mounting. The elevation shows a wall mount.
Who is responsible for clearances if the shade is adjusted on site?
Lutron states that a shade fitted as the factory supplies it has the clearances it needs. Once the installer uses the adjustment features, keeping those clearances is the installer's job.
Lutron warns that some adjustments are not available at the maximum roll diameter.
Does drawing 085425 give a maximum shade size?
No, Lutron drawing 085425 prints only the minimum width, minimum height and minimum light gap. No maximum size is stated on the sheet, and 085705 is the Roller 64 specification submittal.
Other Sivoia QS Roller 64 CAD drawings
CAD drawings for the same Sivoia QS Roller 64 drive class:
All 142 Sivoia QS CAD drawingsDocuments used with 085425
Lutron drawing 085424 is the dual mount section view, and an unnumbered dual mount (pocket) section is a third sheet. Lutron drawings 085519 and 085520 are the dual shade brackets, and 085705 is the Roller 64 specification submittal.
| Document | Type | Revision | Date |
|---|---|---|---|
| 085705Roller 64 Specification Submittal | Specification Submittal | D | Sep 2025 |
| 045843Roller 64 Installation Guide: WIDR Pocket Mount | Installation Guide | B | Sep 2021 |
| 045929Roller 64 Installation Guide: WIDR, 4″ Fascia Mount Chassis (Regular Roll) | Installation Guide | B | Aug 2023 |
| Roller 64 Revit Family: Ceiling Mount | Revit Family | ||
| Roller 64 Revit Family: Dual (Ceiling Mount) | Revit Family | ||
| Roller 64 Revit Family: Dual (Wall Mount) | Revit Family | ||
| Roller 64 Revit Family: Pocket Mount | Revit Family | ||
| Roller 64 Revit Family: Wall Mount | Revit Family | ||
| 0853144-Group RF Remote Control Specification Submittal | Specification Submittal | C | May 2016 |
| 369847Pico Wireless Control, 4-Button Specification Submittal | Specification Submittal | K | Mar 2024 |
Revisions of 085425
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| A | Not stated | Current. The file on assets.lutron.com. Checked 16 Oct 2026. |
Not covered in 085425, and what to read next
Lutron drawing 085425 gives no section, pocket size, tube diameter, maximum shade size or fixing.
Publisher and citation for document 085425
Lutron Electronics Co., Inc. publishes document 085425, Rev A, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 16 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Sivoia QS?
New Way supplies and installs Lutron Sivoia QS shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 085425 filled in.
