You searched and this document matched it.
See all results045717 · Installation Guide · Rev A · Jan 2019 · English, French, Spanish, Portuguese, Chinese, German, Dutch, Italian · PDF, 2 pages, 2.5 MB
Lutron Sivoia QS Roller Shades Installation Guide: (35V) 5-Output Power Module (Power Panel Enclosure Required) (045717, rev A)
Lutron's installation sheet for the WIN-PS-5CC power module, a five-output module for a compatible Lutron QS power panel.
Lutron 045717 Rev A (January 2019), Sivoia QS Roller Shades Installation Guide: (35V) 5-Output Power Module (Power Panel Enclosure Required). https://assets.lutron.com/a/documents/045717.pdf, via https://newwaykl.com/resources/lutron/roller-shades/sivoia-qs/lutron-sivoia-qs-roller-shades-installation-guide-045717/
About document 045717
Lutron document 045717, Rev A of January 2019, is the WIN-PS-5CC power module installation sheet: compatible panels, ratings, the eight replacement steps, the screw torque, the output LED check and pin troubleshooting.
What guide 045717 covers
Lutron document 045717 has these seven sections. Each link opens the PDF at that page in a new tab.
- Important notes, opens in a new tab page 1
- Ratings and electric shock warning, opens in a new tab page 1
- Steps 1 to 4: remove the old module, opens in a new tab page 1
- Steps 5 and 6: seat the new module, opens in a new tab page 1
- Step 7: the panel's second power module, opens in a new tab page 1
- Step 8: restore power and check LEDs, opens in a new tab page 1
- Translations, opens in a new tab page 2
Specifications in 045717
Lutron document 045717 prints 13 values in the groups the document uses, each with the document's unit. A row names the catalog codes it applies to. The page link beside each group opens the PDF where the group starts.
Electrical
PDF page 1 of 045717, opens in a new tab- Input
- 120 V~ to 240 V~, 50/60 Hz, 1 A (x5)Models: WIN-PS-5CC
- Output, per output
- 35 V DC, 143 mA (x5)Models: WIN-PS-5CC
- Outputs per module
- 5, each with its own LED indicator on the panelModels: WIN-PS-5CC
Environmental
PDF page 1 of 045717, opens in a new tab- Ambient operating temperature
- 32 °F to 104 °F (0 °C to 40 °C)Models: WIN-PS-5CC
- Humidity
- 0 to 90%, non-condensingModels: WIN-PS-5CC
- Location
- Indoor use onlyModels: WIN-PS-5CC
Compatibility
PDF page 1 of 045717, opens in a new tab- Power panels
- Compatible Lutron QS power panels only: QSPS-10PNL, QSPSY-10PNLModels: QSPS-10PNL, QSPSY-10PNL
- Older panel versions
- Some do not support field replacement and need the entire panel replacedModels: QSPS-10PNL, QSPSY-10PNL
- Locating slots and tabs
- 5 slots (A) on the mainboard, 5 tabs (AA) on the moduleModels: WIN-PS-5CC
- Sockets and connectors
- 5 sockets (B) on the mainboard, 5 male connectors (BB) on the moduleModels: WIN-PS-5CC
- Mounting screws
- 4, one through each mounting tabModels: WIN-PS-5CC
- Screw torque
- 6 in-lb (0.7 N·m)Models: WIN-PS-5CC
Installation
PDF page 1 of 045717, opens in a new tab- Installer
- Qualified person, to all national and local codesModels: WIN-PS-5CC
Installation walk-through for 045717
Lutron document 045717 gives eight steps, in the document's order, after the tools and fixings it lists.
The clearance, the check and the warning under a step are the document's own.
Tools
- Pliers, for bent or misaligned pins (step 8)
Fixings
- Four mounting screws, one through each mounting tab of the module
- Screw torque 6 in-lb (0.7 N·m)
Switch off the main supply
Turn off the main source of power to the QS power panel before the module is touched. Lutron document 045717 asks for every power source to be disconnected before the unit is serviced.
Check: Panel isolated at the main source
Warning: Electric shock can cause serious injury or death
Remove the module mounting screws
Take out the four mounting screws of the power module, as the drawing on page 1 shows. The translated versions word this step for replacing an existing module.
Check: All four screws out
Pull out the old module or placeholder
Pull the existing power module, or the module placeholder, straight out of the power panel. Lutron document 045717 asks for a straight pull away from the panel.
Check: Slot empty, mainboard slots and sockets visible
Set the old module aside and mark it
Put the removed module to one side and mark it. The mark keeps the old module from being taken for the new one during the swap.
Check: Old module marked
Align and seat the new module
Line up the five locating tabs (AA) on the new module with the five slots (A) on the mainboard. Line up its five male connectors (BB) with the five sockets (B).
Insert the module as drawn, using the mounting holes as a guide and holding it straight and vertical. Once the alignment is confirmed, press the module in firmly so every connector is fully seated.
Check: All five tabs in their slots and all five connectors fully home
Warning: Hold the module straight and vertical so the tabs and connectors meet their slots and sockets
Fit and tighten the screws
Put one mounting screw through each of the four mounting tabs on the module. Tighten each screw to 6 in-lb (0.7 N·m).
Clearance: Torque 6 in-lb (0.7 N·m)
Check: Four screws in, each at the stated torque
Repeat for the panel's other module
Where the panel's other power module is also being replaced or installed, repeat steps 2 to 6 for that slot. Skip this step when only one module is being changed.
Check: Every module being changed is seated and screwed down
Restore power and check the LEDs
Switch the main source back on and look at the LED at each output served by the new module. All five lit means the installation is complete.
When one stays dark, switch off and take the module out using steps 1 to 3. Look for bent, misaligned or broken pins and straighten bent ones with pliers.
Repeat steps 5 to 8. Broken pins, or LEDs still dark afterwards, go to Lutron Technical Support.
Check: All five output LEDs lit
Warning: Power goes off again before the module comes out for a pin check
Requirements Lutron states in 045717
What the guide requires for a Sivoia QS shade before and during installation:
- Module and panels
- The WIN-PS-5CC suits compatible Lutron QS power panels only, the QSPS-10PNL and QSPSY-10PNL. Some older versions need the entire panel replaced instead, which Lutron Technical Support confirms.
- Input rating
- 120 V~ to 240 V~, 50/60 Hz, 1 A (x5)
- Output rating
- 35 V DC at 143 mA on each of five outputs per module. Lutron prints it with its DC symbol as 35 V-.
- Environment
- Ambient 32 °F to 104 °F (0 °C to 40 °C), 0 to 90% humidity, no condensation. Indoor use only.
- Installer and safety
- A qualified person, to all national and local codes. Every power source disconnected before servicing, because of the electric shock risk.
- Removal
- Four mounting screws out, then the old module or placeholder pulled straight out. The old module is set aside and marked so it is not taken for the new one.
- Alignment
- Five tabs (AA) into five mainboard slots (A), and five male connectors (BB) into five sockets (B). The module goes in straight and vertical, then is pressed home firmly.
- Fixing and torque
- One mounting screw through each of the four mounting tabs, each tightened to 6 in-lb (0.7 N·m)
- Second module
- Steps 2 to 6 are repeated for the panel's other power module when that one is also replaced or fitted.
- Check after power-up
- All five output LEDs of the new module must light.
- A dark LED means power off, module out and a pin check
- Bent pins are straightened with pliers
- Broken pins go to Lutron Technical Support
- Not in the document
- No module dimensions or weight, no panel mounting or line wiring, and no shade cable wiring on the outputs
Questions about document 045717
The answers come from Lutron document 045717 and New Way's record of it.
What is Lutron document 045717?
Lutron's two-page power module installation sheet, P/N 045717 revision A, dated 01/2019, repeated in eight languages.
Which revision of 045717 is current?
Rev A, dated January 2019, is the revision Lutron publishes. New Way checked it against assets.lutron.com on 15 October 2026.
Which roller shades does 045717 cover?
Lutron Sivoia QS roller shades.
Which panels take the WIN-PS-5CC power module?
Lutron document 045717 limits the module to compatible Lutron QS power panels, naming the QSPS-10PNL and the QSPSY-10PNL. Some older versions of those panels need replacing whole, and Lutron document 045717 sends that question to Lutron Technical Support.
What does the WIN-PS-5CC module supply?
Lutron document 045717 prints the module's input and output ratings.
- Input: 120 V~ to 240 V~, 50/60 Hz, 1 A (x5)
- Output: 35 V DC at 143 mA on each of five outputs
How is the module fixed in the panel?
Lutron document 045717 seats the module straight and vertical, so its five tabs and five connectors meet the mainboard. The module is then pressed home and fixed with four screws, each at 6 in-lb (0.7 N·m).
What if an output LED stays off after power-up?
Lutron document 045717 says to switch off, remove the module and look for bent, misaligned or broken pins. Bent pins are straightened with pliers.
Lutron document 045717 sends broken pins, or LEDs that stay dark, to Lutron Technical Support.
Can a QS power panel hold two power modules?
Lutron document 045717 refers to the panel's other power module and repeats steps 2 to 6 for it. Lutron document 045717 also allows for a module placeholder, which comes out the same way as an old module.
Other Sivoia QS installation guides
Installation guides for the same Sivoia QS system:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| 04562030-Output Configurable Power Panel Enclosure, 35V Output Installation Guide | Roller 20 to 300 | B | Jan 2018 |
| 045528Roller Shades Installation Guide: Smart Panel, 120V to 240V Input, 35V Output | Roller 20 to 300 | E | Nov 2017 |
| 045000710 Output Power Panel Power Supply (12 V) Installation Guide | Roller 20 to 300 | A | Jul 2025 |
| 0454114-Group RF Remote Control Installation Guide | Roller 20 to 300 | D | Jan 2015 |
Documents used with 045717
Lutron documents 085335 and 085593 are the 10-output smart and configurable panel specification submittals, 045528 the smart panel installation guide. Lutron documents 045620 and 085592 are the 30-output configurable enclosure installation guide and specification submittal.
Revisions of 045717
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| A | Jan 2019 | Current. The file on assets.lutron.com. Checked 15 Oct 2026. |
Not covered in 045717, and what to read next
Lutron document 045717 gives no panel mounting or wiring, no shade cable wiring on the outputs and no shades-per-output count.
Publisher and citation for document 045717
Lutron Electronics Co., Inc. publishes document 045717, Rev A, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 15 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Sivoia QS?
New Way supplies and installs Lutron Sivoia QS shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 045717 filled in.
