You searched and this document matched it.
See all results085674 · CAD Drawing · Rev A · English · PDF, DWG, DXF
Lutron Sivoia QS Roller 64 CAD Drawing: WIDR Corner to Corner Regular Roll (085674)
Lutron's CAD drawing of the Roller 64 WIDR corner to corner installation, where two shades meet at a corner.
Lutron 085674 Rev A, Sivoia QS Roller 64 CAD Drawing: WIDR Corner to Corner Regular Roll. https://assets.lutron.com/a/documents/085674_roller_64_widr_corner_to_corner_regular_roll.pdf, via https://newwaykl.com/resources/lutron/roller-shades/sivoia-qs/lutron-sivoia-qs-roller-64-cad-drawing-085674/
About document 085674
Lutron drawing 085674, Rev A, is the two-page corner to corner drawing: typical details and light gaps on page 1, bracket details, roll-up, deductions and projection adjust on page 2, as PDF, DWG and DXF.
What drawing 085674 covers
Lutron document 085674 has these eight sections. Each link opens the PDF at that page in a new tab.
- Corner to corner typical details, wall bracket shown, opens in a new tab page 1
- Light gaps at maximum roll, regular and reverse, opens in a new tab page 1
- Clearance note and adjustment features, opens in a new tab page 1
- Bracket details in top views, four mount conditions, opens in a new tab page 2
- Maximum roll-up and roll tube centerline, opens in a new tab page 2
- Measurement deductions for the 90 degree corner, opens in a new tab page 2
- Projection adjustment ranges, opens in a new tab page 2
- Title blocks with scale, page number and revision, opens in a new tab page 1
Specifications in 085674
Lutron document 085674 prints 18 values in the groups the document uses, each with the document's unit. The page link beside each group opens the PDF where the group starts.
Typical details
PDF page 1 of 085674, opens in a new tab- Bracket shown
- Wall bracket
- System height and mounting
- Refer to the section drawing
Auxiliary views
PDF page 1 of 085674, opens in a new tab- Regular roll light gap at maximum roll
- 3.8 in typical (inches only)
- Reverse roll light gap at maximum roll
- 0.5 in (13 mm)
- Scale noted beside one view (sheet scale 1/5)
- 1/6
- Top views labeled
- Ceiling, pocket, wall, fascia (pocket drawn as a dashed line; fascia marked not recommended)
- Maximum roll-up, ceiling and wall views
- 3.30 in (84 mm)
- Roll tube centerline, ceiling and wall views
- 1.96 in (50 mm)
- Measurement deduction, ceiling and wall views
- 3.36 in (85 mm)
- Measurement deduction, pocket view
- 4.00 in (102 mm)
- Projection adjust, ceiling view
- -0.25 in/+0.25 in (inches only)
- Projection adjust, wall view
- -0.5 in/+0 in (inches only)
- Fascia view
- Not recommended; no values printed
- Deduction basis
- Minimum recommended deductions, 90 degree corner, applied to both shades
Scale, page, revision
PDF pages 1 and 2 of 085674, opens in a new tab- Page 1 scale
- 1/5
- Page 2 scale
- 1/4
- Revision
- A, on both pages
- Pages
- 2
Facts Lutron states in 085674
The values Lutron document 085674 states, as published:
- Shade covered
- Two Roller 64 WIDR shades meeting corner to corner, wall bracket shown
- Light gap, regular roll
- 3.8 in typical at maximum roll, printed in inches only
- Light gap, reverse roll
- 0.5 in (13 mm) at maximum roll
- Maximum roll-up
- 3.30 in (84 mm), on the ceiling and wall top views of page 2
- Roll tube centerline
- 1.96 in (50 mm), on the ceiling and wall top views of page 2
- Deduction, ceiling and wall mounts
- 3.36 in (85 mm), on the top views of page 2
- Deduction, pocket mount
- 4.00 in (102 mm), on the pocket top view
- Deduction basis
- Minimum recommended deductions, based on a 90 degree corner and applied to both shades
- Projection adjust, ceiling mount
- -0.25 in/+0.25 in, printed in inches only
- Projection adjust, wall mount
- -0.5 in/+0 in, printed in inches only
- Mount conditions, top views
- Ceiling, pocket, wall and fascia
- Fascia view
- Marked not recommended
- Pocket view
- Draws the pocket as a dashed line
- Scale, page and revision
- Page 1, auxiliary views, at 1/5, one view noted at 1/6
- Page 2, top views, at 1/4
- Revision A on both pages, no date printed
- System height and mounting
- Not on this drawing, which refers the reader to the section drawing
- Clearances as supplied
- A shade installed as supplied by the factory has the clearances it needs
- Adjustment features
- Lutron makes the installer responsible for keeping proper clearances once adjustment features are used
- Adjustment at maximum roll
- Not all adjustments are available at the maximum roll diameter
- File formats
- PDF, DWG and DXF
Questions about document 085674
The answers come from Lutron document 085674 and New Way's record of it.
What is Lutron document 085674?
Lutron's CAD drawing of the Roller 64 WIDR corner to corner installation, where two shades meet at a corner. Lutron drawing 085674, Rev A, is the two-page corner to corner drawing: typical details and light gaps on page 1, bracket details, roll-up, deductions and projection adjust on page 2, as PDF, DWG and DXF.
Which revision of 085674 is current?
Rev A is the revision Lutron publishes. New Way checked it against assets.lutron.com on 16 October 2026.
Which roller shades does 085674 cover?
Lutron Sivoia QS roller shades in the Roller 64 drive class.
How do the regular and reverse roll light gaps differ?
Lutron drawing 085674 prints 3.8 in typical for the regular roll and 0.5 in (13 mm) for the reverse roll. Lutron takes both light gaps at maximum roll, on page 1.
What measurement deductions does Lutron recommend?
Lutron prints 3.36 in (85 mm) on the ceiling and wall top views and 4.00 in (102 mm) on the pocket top view. Lutron calls them minimum recommended deductions, based on a 90 degree corner and applied to both shades.
Lutron's fascia view prints no deduction and is marked not recommended.
Which mount conditions do the top views cover?
Lutron labels the page 2 top views ceiling, pocket, wall and fascia. Lutron draws the pocket as a dashed line and marks the fascia view not recommended.
Lutron shows the wall bracket on page 1 and refers to the section drawing for system height and mounting.
What projection adjustment ranges does Lutron print?
Lutron prints -0.25 in/+0.25 in on the ceiling top view, in inches only. Lutron's wall top view prints -0.5 in/+0 in.
Lutron prints the roll tube centerline as 1.96 in (50 mm) on both views.
What does Lutron say about clearances when adjustment features are used?
Lutron states that a shade installed as supplied by the factory has all the clearances it needs. Once the adjustment features are used, Lutron makes the installer responsible for keeping proper clearances.
Lutron notes that not every adjustment is available at the maximum roll diameter.
Other Sivoia QS Roller 64 CAD drawings
CAD drawings for the same Sivoia QS Roller 64 drive class:
| Document | Drive class | Revision | Date |
|---|---|---|---|
| 085675Roller 64 CAD Drawing: WIDR Corner Staggered Regular Roll | Roller 64 | A | |
| 085673Roller 64 CAD Drawing: WIDR Butt and Pass Corner Solution | Roller 64 | A | |
| 085672Roller 64 CAD Drawing: WIDR Shade Bracket, Detail Drawing | Roller 64 | A | |
| 085668Roller 64 CAD Drawing: WIDR, 4” (103mm) Pocket, Section View | Roller 64 | A |
Documents used with 085674
Lutron's other Roller 64 WIDR corner drawings are 085675 (staggered roll) and 085673 (butt and pass). Lutron's 4 in (103 mm) pocket section view is 085668, the universal bracket detail 085672 and the pocket mount installation guide 045843.
| Document | Type | Revision | Date |
|---|---|---|---|
| 045843Roller 64 Installation Guide: WIDR Pocket Mount | Installation Guide | B | Sep 2021 |
| 085705Roller 64 Specification Submittal | Specification Submittal | D | Sep 2025 |
| 045929Roller 64 Installation Guide: WIDR, 4″ Fascia Mount Chassis (Regular Roll) | Installation Guide | B | Aug 2023 |
| 045930Roller 64 Installation Guide: WIDR, 4″ Fascia Mount Chassis (Reverse Roll) | Installation Guide | B | Aug 2023 |
| Roller 64 Revit Family: Ceiling Mount | Revit Family | ||
| Roller 64 Revit Family: Dual (Ceiling Mount) | Revit Family | ||
| Roller 64 Revit Family: Dual (Wall Mount) | Revit Family | ||
| Roller 64 Revit Family: Pocket Mount | Revit Family | ||
| Roller 64 Revit Family: Wall Mount | Revit Family | ||
| 0853144-Group RF Remote Control Specification Submittal | Specification Submittal | C | May 2016 |
Revisions of 085674
This page always shows the revision Lutron publishes today. Lutron replaces the file in place and does not keep earlier revisions online.
| Revision | Date | Status |
|---|---|---|
| A | Not stated | Current. The file on assets.lutron.com. Checked 16 Oct 2026. |
Not covered in 085674, and what to read next
Lutron drawing 085674 gives no system height, bracket dimensions or mounting fixings, and points to the section drawing for them.
Publisher and citation for document 085674
Lutron Electronics Co., Inc. publishes document 085674, Rev A, and serves it from assets.lutron.com. New Way hosts no copy and last checked the file there on 16 October 2026.
Lutron and Sivoia QS are trademarks of Lutron Electronics Co., Inc.
Reviewed by Edmond Hong, Technical Specialist, New Way.
Specifying Sivoia QS?
New Way supplies and installs Lutron Sivoia QS shading in Malaysia and Singapore. A New Way specifier can check your shade schedule and drawings before you submit.
The form opens with document 085674 filled in.
